ABB UNS2881B-P,V1 3BHE009319R0001向船舶應用推進

滾動LED狀態指示燈

滾動LED顯示屏指示模塊的工作狀態，如下所示：初始化消息

代碼消息

啟動/DDOK模塊正在初始化

Ladd模塊正在等待來自的所需模塊配置數據

用于配置應用程序端口的梯形圖邏輯等待處理器連接模塊在初始化期間未連接到處理器

? 處理器上未加載示例梯形圖邏輯或AOI

? 模塊位于不同的插槽中在梯形圖邏輯/AOI中配置

? 處理器未處于RUN或REM RUN模式

上次配置：<日期>表示模塊更改其IP的最后日期

住址您可以通過以下方式更新模塊日期和時間

模塊的網頁，或使用可選MVI56E插件指示

通電和每次重新配置后，模塊將顯示應用程序端口的配置。這個信息包括：客戶端模塊未獲得足夠電源或不安全插入機架。配置期間也可能關閉下載

綠色MVI56E-SIE工作正常。紅色最常見的原因是模塊檢測到

應用程序端口操作期間的通信錯誤。

以下情況也可能導致紅色LED：

? 固件正在啟動期間初始化

? 固件檢測到板載硬件問題

啟動期間

? 啟動期間應用程序端口硬件故障

? 模塊正在關閉

? 由于ColdBoot或WarmBoot，模塊正在重新啟動梯形圖邏輯或調試菜單的請求模塊未獲得足夠的電源或不安全插入機架。綠色模塊工作正常。

紅色模塊檢測到內部錯誤或正在已初始化。如果LED保持紅色超過10秒模塊不工作。將其從機架上拆下并重新插入重新啟動其內部程序。

ERR紅色OFF蓄電池電壓正常且工作正常。

ON蓄電池電壓低或不存在蓄電池。允許電池充電，將模塊插入機架24小時。如果ERR LED仍不熄滅，請聯系ProSoft技術，因為電池不是用戶可維修的部件。

Scrolling LED Status Indicators

The scrolling LED display indicates the module's operating status as follows:

Initialization Messages

Code Message

Boot / DDOK Module is initializing

Ladd Module is waiting for required module configuration data from

ladder logic to configure the application port(s)

Waiting for Processor Connection Module did not connect to processor during initialization

? Sample ladder logic or AOI is not loaded on processor

? Module is located in a different slot than the one

configured in the ladder logic/AOI

? Processor is not in RUN or REM RUN mode

Last config: <date> Indicates the last date when the module changed its IP

address. You can update the module date and time through

the module’s web page, or with the Optional MVI56E Add-On

Instruction.

After power up and every reconfiguration, the module will

display the configuration of the application port(s). The

information consists of:

Client The module is not receiving adequate power or is not securely

plugged into the rack. May also be OFF during configuration

download.

GREEN The MVI56E-SIE is working normally.

RED The most common cause is that the module has detected a

communication error during operation of an application port.

The following conditions may also cause a RED LED:

? The firmware is initializing during startup

? The firmware detects an on-board hardware problem

during startup

? Failure of application port hardware during startup

? The module is shutting down

? The module is rebooting due to a ColdBoot or WarmBoot

request from the ladder logic or Debug Menu The module is not receiving adequate power or is not securely

plugged into the rack.

GREEN The module is operating normally.

RED The module has detected an internal error or is being

initialized. If the LED remains RED for over 10 seconds, the

module is not working. Remove it from the rack and re-insert it

to restart its internal program.

ERR Red OFF The battery voltage is OK and functioning.

ON The battery voltage is low or battery is not present. Allow

battery to charge by keeping module plugged into rack for 24

hours. If ERR LED still does not go off, contact ProSoft

Technology, as the battery is not a user-serviceable item.