3BSE031154R1模擬量電子配套模塊
FBM242終端組件是I/A系列DIN軌道安裝FBM子系統現場接線終端系列的一部分。每個FBM242終端組件及其相關終端電纜在16個2線外部源固態開關輸出和FBM242通道隔離外部源離散輸出接口模塊之間提供有源信號接口和連接。終端組件的輸出開關支持外部電源120 V ac或125 V dc。每通道保險絲將輸出電流限制在最大2 a。主要特點包括：?組合腳，支持32或35 mm DIN導軌安裝?多個集成標記系統?獨特的系列顏色?常開，固態開關輸出?有源每通道輸出熔斷器保護，帶雙向熔斷器指示（直流極性無關）?每通道輸出刀斷開和測試插座。信號輸出（a）16通道，由終端組件提供的外部源固態開關通道隔離額定值（a）最大2 a時為132 V ac，帶電阻負載，或最大20 mH電感負載，不帶緩沖金屬氧化物壓敏電阻（MOV），最大2 a處為150 V dc，帶阻性負載，或50 mH最大電感負載，帶緩沖二極管，INRUSH CURRENT 20 a峰值，16 ms最大泄漏電流<1 mA ON RESTANCE<100米? 20°C時最大散熱7.0 W
在第14節（IPU-237）中添加以下變更
第14-15頁，在表14-11中，關于LED 1-8添加以下內容：如果模擬通道正常，則LED點亮。然后，如果HART消息交換正確發生，LED將閃爍100毫秒。如果模擬信道正常，并且模塊發送消息但未收到正確響應，則LED將閃爍400毫秒。從版本0C開始，RSR固件支持級聯PI配置，其中PI 1的輸出用作PI 2的目標位置輸入。支持級聯操作的其他功能包括選擇直接/間接PI操作的標志，以及稱為“后退”的防纏繞功能。這些新功能中的一些實際上獨立于級聯，但所有這些都在本文中詳細描述。第22-9頁，刪除校準模式部分下完全校準項目符號第二段（任意極限…10.0伏）后的所有剩余段落（六）：第22-9.頁，添加以下信息代替上述項目中刪除的段落：當要求完全校準時，閥門首先行程至0%。在0%時，解調器增益被調整，直到反饋電壓接近10伏。此時解調器增益是最大可能的解調器增益。然后閥移動到100%。如果電壓大于10伏或超出刻度，解調器增益將降低，并讀取電壓讀數。該讀數為100%標定閥。然后，閥門移動至0%，并讀取電壓讀數。該讀數為0%校準值。確定0%校準閥后，新值寫入EE存儲器。
INTRODUCTION
The FBM242 Termination Assembly is part of the I/A Series DIN rail mounted FBM subsystem field wiring termination family. Each FBM242 Termination Assembly and its associated termination cable provide active signal interfacing and connection between sixteen 2-wire externally sourced solid-state switched outputs and the FBM242 Channel Isolated Externally Sourced Discrete Output Interface Module. The termination assembly’s output switching supports externally sourced 120 V ac or 125 V dc. Per channel fuses limit output current to a maximum of 2 A. FEATURES Key features include: ? Combination foot that supports 32 or 35 mm DIN rail mounting ? Multiple, integrated marking systems ? Distinct family group color ? Normally open, solid-state switched outputs ? Active per channel output fuse protection with bidirectional blown fuse indication (dc polarity independent) ? Per channel output knife disconnect and test sockets.Signal Output(a) 16 channel, externally sourced solid-state switch Channel isolation provided by termination assembly RATING(a) 132 V ac at 2 A maximum with resistive load or 20 mH maximum inductive load without snubber metal oxide varistor (MOV) 150 V dc at 2 A maximum with resistive load or 50 mH maximum inductive load without snubber diode INRUSH CURRENT 20 A peak for 16 ms maximum LEAKAGE CURRENT <1 mA ON RESISTANCE <100 m ? at 20°C HEAT DISSIPATION 7.0 W maximum
Add the Following Changes to Section 14 (IPU-237)
Page 14-15, In Table 14-11, regarding LED’s 1-8 add the following: If the analog channel is healthy, the LED is illuminated. Then, if a HART message exchange occurs correctly, the LED is blinked off for 100 mSec. If the analog channel is healthy, and if the module sends a message and does not receive a correct response, the LED is blinked off for 400 mSec.Starting with revision 0C, RSR firmware supports a cascaded PI configuration in which the output of PI 1 is used as the target position input for PI 2. Additional features to support cascading operation are flags to select direct/indirect PI operation, and an anti-windup feature called “retreat”. Some of these new features are actually independent of cascading, but all are described in detail in this document. Page 22-9, Delete all of the remaining paragraphs (six) after the second paragraph (Arbitrary limits...10.0 volts.) in the Full Calibration bullet under the Calibrate Mode Section: Page 22-9, Add the following information in place of the deleted paragraphs in above item: When full calibration is requested, the valve first travels to 0%. At 0%,demodulator gain is adjusted until the feedback voltage is near 10 volts. The demodulator gain at this point is the maximum possible demodulator gain. Then the valve travels to 100%. If the voltage is greater than 10 volts, or off-scale, demodulator gain is reduced, and a reading of the voltage is taken. This reading is the 100% calibration valve. Then the valve travels to 0% and a voltage reading is taken. This reading is the 0% calibration value. After the 0% calibration valve is determined, the new values are written to EE memory.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
