KONGSBERG RCU510船舶控制卡件
傳感器信號監測SIGNAL（信號）按鈕的操作允許監控所選通道傳感器信號值。顯示的參數取決于安裝在所選通道卡上的傳感器驅動模塊的類型。要進入傳感器信號監測操作，請執行以下操作：（1）按住所需通道卡RESET/SELECT（重置/選擇）按鈕約1.5秒，直到所選圖標出現在通道顯示器上。（2） 按下SIGNAL（信號）按鈕，所選通道卡顯示屏將指示傳感器信號。顯示的值將取決于安裝在通道卡上的傳感器驅動模塊的類型，如下所示：a.催化傳感器驅動模塊顯示屏將顯示在01和02之間測得的帶電電橋電壓（單位：mV）。02是通道卡上惠斯通電橋后半部的中心點。b、 4-20mA傳感器驅動模塊顯示屏將以mA為單位顯示傳感器回路電流。（3）按下（）或（）按鈕或等待30秒退出信號模式。4.7查看時鐘/日歷操作時鐘按鈕將導致當前時間和日期顯示在所選通道卡上。注意：此操作需要選擇控制卡，但此操作對所選控制卡沒有影響，該控制卡僅用作顯示設備。
進入時鐘/日歷操作
如下操作：（1）按住所需的通道卡RESET/SELECT（重置/選擇）按鈕約1.5秒，直到所選圖標出現在通道顯示器上（2）按下CLOCK（時鐘）按鈕，所選通道卡顯示器將指示當前時間。注：時鐘采用24小時制。（3） 再次按下CLOCK（時鐘）按鈕，所選通道卡顯示屏將顯示當前日期、月份和年份。注：1.根據系統配置，日和月的顯示格式可以是DD.MM或MM.DD。2.進一步按下CLOCK（時鐘）按鈕將在時間和日期之間切換顯示。（4） 按下（）或（）按鈕或等待30秒以退出時鐘模式。4.8維護記錄打印可以使用工程卡啟動每個通道狀態的詳細打印輸出或整個機架的匯總。數據以ASCII文本格式饋送至工程卡前面板上的工程串行端口。要輸出每個通道卡的維護記錄，請執行以下操作：（1）將RS232打印機插入工程卡串行端口。（2）按住所需通道卡RESET/SELECT（重置/選擇）按鈕約1.5秒，直到所選圖標出現在通道顯示器上。（3） 同時按下向上和向下按鈕。輸出以下數據時，所選通道卡將顯示PRN
Sensor Signal Monitoring
The operation of the SIGNAL push-button allows the monitoring of the selected channels sensor signal value. The displayed parameter is dependent upon the type of sensor drive module fitted to the selected channel card. To enter the sensor signal monitoring operation, proceed as follows: (1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears on the channel display. (2) Push the SIGNAL push-button and the selected channel card display will indicate the sensor signal. The displayed value will depend on the type of sensor drive module fitted to the channel card as follows: a. Catalytic Sensor Drive Module The display will show the live bridge voltage measured between 01 and 02 in mV. 02 is the centre point of the second half of the Wheatstone bridge which is on the channel card. b. 4 - 20mA Sensor Drive Module The display will show the live sensor loop current in mA. (3) Push the ( ) or ( ) push buttons or wait 30 seconds to exit the SIGNAL mode. 4.7 View Clock/Calendar The operation of the CLOCK push-button will cause the present time and date to be displayed on a selected channel card. Note: This operation requires a control card to be selected but the operation has no effect on the selected control card, which is used as a display device only.
To enter the clock/calendar operation
proceed as follows: (1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears on the channel display (2) Push the CLOCK push-button and the selected channel card display will indicate the present time. Note: The clock uses the 24 hour format. (3) Push the CLOCK push-button a second time and the selected channel card display will indicate the present day, month and year. Notes: 1. The display format for day and month can read either DD.MM or MM.DD depending on the configuration of the system. 2. Further pushes of the CLOCK push-button will toggle the display between time and date. (4) Push the ( ) or ( ) push-buttons or wait 30 seconds to exit the CLOCK mode. 4.8 Maintenance Record Print Out A detailed printout of the status for each channel or a summary of the whole rack can be initiated using the Engineering Card. The data is fed in ASCII text format to the engineering serial port on the Engineering Card front panel. To output the maintenance record for each channel card, proceed as follows: (1) Plug a RS232 printer into the Engineering card serial port. (2) Push and hold the required channel card RESET/SELECT push button for approximately 1.5 seconds until the selected icon appears on the channel display. (3) Push the up ( ) and down ( ) buttons simultaneously. The selected channel card will display PRN while outputting the following data
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
