產品詳情介紹
UR8GH保護繼電器
一次打開一個單元直到電源電流能力的總和超過所消耗的負載電流。5.使用電壓控制平衡每個單元電壓，以獲得相等的輸出電流。6.將電流控制設置為僅限制在運行電流之上，這樣，如果一個裝置的輸出電壓向上漂移，它就會受到電流限制，而不是承載過多的負載電流份額。重要事項：當裝置包含過電壓選項時，未經咨詢電子測量工程人員，請勿將其并聯。如果其中一個并聯單元在未正確并聯OVP選項的情況下進入過電壓，將發生不可修復的損壞。在此配置中，指定為主電源的電源用于控制所有其他電源（稱為從電源）的電壓和電流操作。1.斷開所有從機的以下跳線：TB3-13和14 TB3-9、10和11 2.在所有從機TB3-10和12之間連接跳線。3.如圖9A或9B所示，連接每個電源的主電源TB3-12和TB3-13。4.將每個從機的電壓控制調整到最大CW。5.正負電壓連接見圖9A或9B。6.打開每個從屬設備，然后打開主設備。7.根據需要的輸出電壓或電流調整主控。每個電源的輸出引線必須對電源附近的負載點具有相等的電阻，以確保均勻分配。
串聯操作
只需將一個單元的負極輸出端子連接到另一個單元正極輸出端子，即可串聯兩個EMHP電源。每個單元的調節功能獨立，總輸出電壓是每個單元輸出電壓的總和。注意：任何輸出端子上的電壓相對于底盤接地不得超過600V。請咨詢Electronic Measurements，股份有限公司工程部，了解兩個以上電源的串聯操作。遠程儀表遠程電壓表可連接在端子TB3-2（位置）和TB3-7（負極）之間。如果同時使用遙感，遠程電壓表將指示負載電壓。為了指示電源輸出端子處的電壓，在端子TB3-1（位置）和TB3-8（負極）之間連接遠程電壓表。遠程毫伏表可連接在端子TB3-12（負極）和TB3-14（位置）之間。除非另有規定，否則這些端子上的0至100毫伏電壓表示輸出電流從零到滿額定值（見主示意圖）。為了補償遠程長電流表引線中的電壓降，將滿標度靈敏度小于100毫伏的電流表移動裝置與校準電阻器串聯使用。遠程儀表的導線應扭曲，如果存在強交流或射頻場，則應屏蔽導線。屏蔽的一端應接地至端子TB3-14，另一端保持浮動
Turn units on one at a time
until the sum of the power supply current capabilities exceeds the load current drawn. 5. Using the voltage controls balance each unit voltage for equal output current. 6. Set the current controls to limit just above running current so that if a unit's output voltage drifts upward, it will become current limited rather than carry an excessive share of load current. IMPORTANT: When the units contain the overvoltage option do not connect them in parallel without consulting the Engineering Staff of Electronic Measurements. Irreparable damage will occur if one of the paralleled units goes into overvoltage without proper paralleling of the OVP option.In this configuration, the power supply designated the master is used to control the voltage and current operation of all other supplies, referred to as slaves. 1. Disconnect the following jumpers of all slaves: TB3-13 and 14 TB3-9, 10 and 11 2. Connect a jumper between TB3-10 and 12 of all slaves. 3. Connect the master supply TB3-12 and TB3-13 of each supply as shown in either Figure 9A or 9B. 4. Adjust the voltage control of each slave to maximum CW. 5. See Figure 9A or 9B for + and - voltage connection. 6. Turn each slave on and then the master. 7. Adjust the master for required output voltage or current. The output leads from each power supply must be of equal resistance to a point of load near the supply to assure equal sharing.
SERIES OPERATION
Two EMHP power supplies can be operated in series simply by connecting the negative output terminal of one unit to the positive output terminal of the other. The adjustment of each unit functions independently and the total output voltage is the sum of each unit output voltage. NOTE: The voltage at any output terminal must never exceed 600V with respect to chassis ground. Consult Electronic Measurements, Inc. Engineering Department for series operation of more than two supplies.REMOTE METERS A remote voltmeter may be connected between terminals TB3-2 (pos.) and TB3-7 (neg.). If remote sensing is also being used, the remote voltmeter will indicate the voltage at the load. To indicate the voltage at the power supply output terminals connect the remote voltmeter between terminals TB3-1 (pos.) and TB3-8 (neg.). A remote millivoltmeter may be connected between terminals TB3-12 (neg.) and TB3-14 (pos.). A voltage of 0 to 100mv across these terminals indicates output current from zero to full rating unless otherwise specified (see main schematic). To compensate for voltage drops in long remote ammeter leads a meter movement having a full-scale sensitivity of the less than 100mv is used in series with a calibrating resistor. The leads to the remote meters should be twisted, and if strong AC or RF fields are present, the leads should be shielded. One end of the shield should be grounded to terminal TB3-14 and the other end left floating
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
