產品內容介紹
FISHER CL6821X1-A5輸出模塊
接線板要在I/O模塊和現場設備之間布線，請在I/O模塊上安裝一個壓力夾端子或KS電纜接口適配器。當使用壓力鉗端子時，I/O模塊可以直接與現場設備連接。使用KS電纜接口適配器時，I/O模塊通過端子板與現場設備連接。有兩種類型的壓力鉗接線端子：單冗余型和雙冗余型。使用雙冗余類型，可以在接線板上配置雙冗余I/O模塊。此外，MIL連接器電纜可以直接連接到輸入/輸出模塊，而無需將接線板安裝到輸入/輸入模塊。MIL連接器電纜由客戶提供。提供了一個電纜連接器蓋（ACCC01），以防止MIL連接器電纜松動。標題為“I/O模塊和接線板組合”的表格列出了I/O模塊、接線板和連接器電纜之間的連接。本質安全區域和非本質安全區域之間的距離應大于等于50 mm。帶有內置屏障的模塊應安裝在一個節點單元中與其他模塊區域分開的區域。如果是AN?10?, 必須在帶有內置屏障的模塊區域和其他模塊區域之間安裝絕緣隔板（零件號T9083NA）。如果是AFV10? 和AFV30?, 必須安裝絕緣隔斷套件（零件號T9083ND），以保持本安區和非本安區之間的距離。示例：隔離an中的兩個區域時?10D，其中“（S）”表示單冗余，“（D）”表示雙冗余。示例：在an中安裝模塊時?10D，其中“（S）”表示單冗余，“（D）”表示雙冗余。
機柜內安裝
如果機柜上部空間中有風扇，請將模塊安裝在比風扇低3個單元（1個單元=44.45 mm）的位置。環境工作溫度條件下的安裝限制當節點（-20至70℃-可選溫度環境）在溫度環境（60至70℃）下使用時，請遵循以下限制：ANT10U可以在60至70°C的溫度下使用，與在-20至50°C的溫度下使用相同，無任何附加限制。?可安裝輸入/輸出模塊（IOM）的最大數量：每個節點最多可安裝4個模塊。?在SB401、ANT401、ANT411、ANT502、ANT512、EB501和IOM之間制作一個空插槽（一個或多個）。安裝帶有內置屏障的模塊時，必須在插槽8中安裝絕緣隔板（零件號T9083NA）。?安裝IOM時，在IOM和IOM之間留出一個空插槽（一個或多個）。安裝雙面IOM時，為每個雙面IOM制作一個空插槽（至少兩個插槽）。?最多可以使用8個繼電器輸出模塊（ADR541）。為了保持參考結補償精度，請確保滿足以下條件。壓力鉗端子不應受到輻射熱的影響。有關參考結補償精度的詳細信息，請參閱“模擬I/O模塊”（GS33K50F60-50E）。僅適用于節點的規格?請勿在AAT141安裝的節點下方安裝散熱裝置。?不要將AAT141安裝在氣流直接影響的地方。?不要在CP461和CP451旁邊安裝AAT141。?不要在總線接口模塊SB401、ANT502、ANT512和EB501旁邊安裝AAT141。?AAT141旁邊的可安裝模塊如下。安裝IOM以外的其他IOM時，請在每側制作一個空插槽（一個或多個）。
Terminal Blocks
To wire between I/O Module and field devices, install a pressure clamp terminal or KS cable interface adapter on the I/O Module. When a pressure clamp terminal is used, the I/O Module can be wired directly with the field devices. When the KS cable interface adapter is used, the I/O Module is wired with the field devices via terminal boards. Two types of pressure clamp terminal blocks are available: single and dual-redundant types. Using the dual-redundant type, dual-redundant I/O Modules can be configured on the terminal block. In addition, a MIL connector cable can be connected directly to an I/O Module without installing a terminal block to the I/O Module. The MIL connector cable are furnished by the customer. A cable connector cover (ACCC01) is provided in order to prevent the MIL connector cable from coming loose. The table entitled “Combinations of I/O Modules and Terminal Blocks” lists connections among I/O Modules, terminal blocks and connector cables.Please keep a distance of 50 mm or more between the intrinsically safe area and the non-intrinsically safe area. Modules with built-in barriers should be installed in an area separate from the area of other modules in one node unit. In case of AN?10?, an insulating partition (Part No. T9083NA) must be installed between the area of Modules with Built-in Barrier and the area of other Modules. In case of AFV10? and AFV30?, an insulating partition kit (Part No. T9083ND) must be installed to keep a distance between the intrinsically safe area and the non-intrinsically safe area. Example: When isolating the two areas in an AN?10D as follows where “(S)” indicates Single and “(D)” indicates Dual-Redundant.Example: When installing modules in an AN?10D as follows where “(S)” indicates Single and “(D)” indicates Dual-Redundant.
Installation in Cabinet
If there is a fan in the upper space of the cabinet, install the module in a position that is 3 units (1 unit = 44.45 mm) lower than the fan. Limitations of Installation under the Ambient Operating Temperature Conditions When the node (-20 to 70 ?C - optional temperature environment) is to be used under the temperature environment (60 to 70 ?C), please follow the restrictions below: ANT10U can be used at temperatures from 60 to 70°C without any additional restrictions in the same way as at temperatures from -20 to 50°C. ? Max. number of installable input/output modules (IOM): Up to 4 modules can be installed per node. ? Make an empty slot (one or more) between SB401, ANT401, ANT411, ANT502, ANT512, EB501 and IOM. When installing modules with built-in barriers, insulating partition (Part No. T9083NA) must be installed in slot No. 8. ? When installing IOM, make an empty slot (one or more) between IOM and IOM. When installing duplexed IOM, make an empty slot (at least two slots) for each duplexed IOM. ? Up to 8 relay output modules (ADR541) can be used.To keep the reference junction compensation accuracy, make sure to meet the following conditions. The pressure clamp terminal should not be affected by radiated heat, For details of the reference junction compensation accuracy, refer to “Analog I/O Modules” (GS33K50F60-50E). Specifications for node only ? Do not install a heat-radiating unit beneath the AAT141 installed node. ? Do not install AAT141 in the place where airflow affects directly. ? Do not install an AAT141 next to the CP461 and CP451. ? Do not install AAT141 next to the bus interface modules, SB401,ANT502,ANT512 and EB501. ? The installable modules in the next to AAT141 are as follows. When installing other than following IOM, make an empty slot (one or more ) in each side.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
