ICS TRIPLEX T8403CX控制處理器
自定義應用程序：?jiǎn)螕魡?dòng)向?qū)聊恢械摹安僮髂Ｊ健卑粹o，選擇期望的回路控制模式；速度或扭矩。單擊退出返回啟動向?qū)聊弧?/p>
單擊啟動向?qū)聊恢械恼{(diào)諧按鈕，設置系統帶寬、環路類型以及應用所需的過濾。
執行自動調諧功能時應小心。有些應用程序不是能夠處理軸感測其負載時引起的振動。如果這是有問題的，手動調整驅動器。此外，當負載慣性非常大時帶寬高，此功能可能無法執行。
設置完成：?jiǎn)螕敉顺鲆赞D(zhuǎn)到MOTIONLINK主屏幕。
有關這些功能的說明，請參閱主MOTIONLINK屏幕。
將變量參數保存到EEPROM
將變量參數保存到.SSV文件
恢復工廠變量參數
恢復自定義變量參數
主運動鏈接屏幕
退出MOTIONLINK啟動向?qū)聊粫r(shí)，將顯示此屏幕。所有屏幕
可以從該屏幕訪問上述方法中提到的，并應用于進行更正
在當前系統配置中
設置驅動器變量參數：從配置菜單中，單擊驅動器選項。相同的屏幕顯示如啟動向?qū)聊徊糠炙?。單擊“退出”返回到Main MOTIONLINK屏幕。
設置電機變量參數：選擇配置菜單下的電機選項，您可以獲取與啟動向?qū)聊恢邢嗤膮?shù)屏幕。單擊“退出”返回到Main MOTIONLINK屏幕。
自定義應用程序：通過下拉操作模式列表，您可以選擇模式所需的回路控制（速度、扭矩）。點擊“調整”按鈕，您可以選擇系統帶寬、環路控制類型以及應用所需的濾波。這些都是一樣的啟動向?qū)聊恢械膮?shù)屏幕。單擊“退出”返回主MOTIONLINK屏幕
將可變參數保存到EEPROM：在此屏幕頂部，您可以單擊標記為“RAM/E2
“將修改后的變量從RAM保存到EEPROM。將變量參數保存到.SSV文件：有時，您可能需要備份變量
一個驅動器的參數用于另一個驅動器。為此，必須下拉編輯菜單并選擇備份變量，從驅動器（“接收”按鈕）向編輯器請求信息，并保存（“保存”按鈕）將.SSV格式的內容保存到指定的磁盤位置。
Customizing to Application: Click the “Opmode” button in the Startup Wizard screen to select the mode of loop control desired; velocity, or torque. Click Exit to return to the Startup Wizard screen. Click on the Tune button in the Startup Wizard screen to set the system bandwidth, the type of loop control, and the filtering necessary for the application. Caution should be used when executing the AutoTune feature. Some applications are not capable of handling the vibration caused as the shaft senses its load. If this is in question, manually tune the drive. Also, when the load inertia is very large and the selected bandwidth is high, this feature may fail to perform. Setup Complete: Click EXIT to go to the Main MOTIONLINK screen. For explanation on these functions, refer to the Main MOTIONLINK screen. Saving Variables Parameters to EEPROM Saving Variables Parameters to .SSV file Restoring Factory Variable Parameters Restoring Custom Variable Parameters Main MOTIONLINK Screen This screen appears the when you exit out of the MOTIONLINK Startup Wizard screen. All the screens mentioned in the method above can be accessed from this screen and should be used to make corrections in the current system configuration. Setting Drive Variable Parameters: From the Configure menu, click the Drive option. The same screen appears as described in the Startup Wizard screen section. Click Exit to return to Main MOTIONLINK screen. Setting Motor Variable Parameters: Selecting the Motor option under the Configure menu, you can obtain the same parameter screen found in the Startup Wizard screen. Click Exit to return to Main MOTIONLINK screen. Customizing to Application: By dropping down the Operational Mode listing, you can select the mode of loop control desired (velocity, torque). Clicking the “Tune” button, you can select the system bandwidth, the type of loop control, and the filtering necessary for the application. These are the same parameter screens found in the Startup Wizard screen. Click Exit to return to Main MOTIONLINK Screen. Saving Variable Parameters to EEPROM: At the top of this screen, you can click the button labeled “RAM/E2 ” to save the modified variables from RAM to EEPROM. Saving Variable Parameters to .SSV file: Occasionally, you may desire to backup the variable parameters from one drive for use in another. To do this, you must pull down the Edit menu and select Backup Variables, request the information from the drive (“Receive” button) into the editor, and save (“Save” button) the contents in a .SSV format to a specified disk location.
