主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
3BHL000389P0104可控硅模塊
E/F檢測器有三種可選的操作模式，通過參數設置選擇所需參數
“GndFaultMode”。E/F檢測可以基于測量中性電流單獨或與中性相結合
電壓第四種可能性是不測量接地回路即僅測量相-相回路。
這個以下備選方案可供選擇：阻塞（僅測量相間回路）I0
I0和U0 I0或U0。最高“3I0min”設置的標準為： E/F探測器必須拾取所有接地良好的E/F
系統和未接地系統或帶消弧線圈系統上的所有越野故障，前提是它們位于
低阻抗起動器的范圍。最低“3I0min”設置的標準為：
E/F探測器不得拾取未接地的E/F
系統或具有消弧線圈的系統， E/F檢測器不得拾取相位故障，盡管c、 t.錯誤可能導致假中性電流。
建議設置為“3I0min”=0.5 IN。
如果不可能找到滿足這兩個條件的設置在這些條件下，必須使用中性電壓（3U0min除中性電流外的測量。
3.5.31.2.5.相位優先邏輯
越野故障所需的相位優先邏輯為：借助參數“PhaseSelMode”進行選擇。
在固體接地系統中，“相位模式”參數為通過將其設置為“固體接地”禁用。
不接地系統和帶消弧線圈系統中的所有繼電器必須設置為相同的相位偏好
思維方式因此，在選擇8個備選方案之一之前，必須知道系統中使用的邏輯：
RTS（R）循環欠壓起動器（烏韋克）
欠壓起動器與接通故障功能和轉換跳閘方案
灌封和推土不直接（見第3.5.31.7節）。與額定電壓相關的相應拾取值設置為：
借助參數“Uweak”，其設置范圍為0以0.01。
There are three alternative operating modes for the E/F detector,
the desired one being chosen by the setting of the parameter
‘GndFaultMode’. E/F detection can be based on measurement
of the neutral current alone or in combination with the neutral
voltage. The fourth possibility is not to measure the ground loop
at all, i.e. only the phase-to-phase loop is measured. The
following alternatives are available for selection:
blocked (only measures the phase-to-phase loops)
I0
I0 AND U0
I0 OR U0.
The criterion for the highest ‘3I0min’ setting is:
the E/F detector must pick-up for all E/F's in solidly grounded
systems and for all cross-country faults on ungrounded systems or systems with Petersen coils, providing they lie within
the reach of the underimpedance starters.The criteria for the lowest ‘3I0min’ setting are:
the E/F detector must not pick up for an E/F on ungrounded
systems or systems with Petersen coils,
the E/F detector must not pick up for phase faults, although
c.t. errors can cause false neutral currents.
The recommended setting is ‘3I0min’ = 0.5 IN.
Should it not be possible to find a setting, which satisfies both
these conditions, the neutral voltage (3U0min) must be used for
measurement in addition to the neutral current.
3.5.31.2.5. Phase preference logic
(see Section 4.8.1.4.)
The desired phase preference logic for cross-country faults is
chosen with the aid of the parameter ‘PhaseSelMode’.
In solidly grounded systems, the ‘PhaseSelMode’ parameter is
disabled by setting it to ‘solid ground’.
It is essential for all the relays in ungrounded systems and systems with Petersen coils to be set to the same phase preference
logic. The logic in use in a system must therefore be known before one of the 8 alternative schemes can be selected:
RTS(R) cyclicUndervoltage starters
(Uweak)
The undervoltage starters are used in conjunction with the
switch-onto-fault function and the transfer tripping schemes
POTT and PUTT NONDIR (see Section 3.5.31.7.). The corresponding pick-up value is set in relation to the rated voltage with
the aid of the parameter ‘Uweak’, which has a setting range of 0
to 2 UN in steps of 0.01.
