3BHE036342R0101 DCS卡件
3.3.7珠子mA按鈕當操作胎圈mA按鈕時，所選的
催化控制卡提供該卡傳感器頭的指示
現在的如果工程關鍵是：安裝在工程卡上。報警按鈕當操作報警按鈕時，所選的
控制卡提供該卡的級別和類型指示（上升或下降）的每個報警電平（A1、A2、A3、STEL、LTEL）。
如果工程鑰匙安裝在工程卡上，調整可以在預先定義的限制范圍內達到報警水平，并且測試設施可用。該設施允許每次報警操作
待檢查，如果需要，其相關輸出繼電器應：鍛煉。
3.3.9信號按鈕
當操作信號按鈕時，所選控制卡提供該卡傳感器信號的指示：
跟隨：a、 4-20mA控制卡-回路電流（mA）。
b、 催化控制卡-催化橋輸出（靈敏度），單位為mV。
3.3.10歸零按鈕
零點按鈕只能在工程鍵處于以下狀態時使用：
安裝在工程卡上，用于校準選定的控制卡。
3.3.11量程按鈕
只有在工程鍵為安裝在工程卡上，用于校準選定的控制卡。
3.3.12第1跨按鈕第1跨按鈕只能在工程
鑰匙安裝在工程卡上，用于校準量程安裝到選定催化控制裝置的新催化傳感器的點卡片
該功能用于提供指示，與隨后的正常量程調整，a的輸出靈敏度催化傳感器，并自動指示中毒或損失傳感器性能。3.3.13時鐘按鈕
當操作時鐘按鈕時，所選的控制卡提供機架的時間和日期指示時鐘
3.3.7 BEAD mA Push-button
When the BEAD mA push-button is operated, the display of the selected
Catalytic Control Card provides an indication of that card's sensor head
current.
Adjustments to this current can also be made if the Engineering Key is
fitted to the Engineering Card.ALARMS Push-button
When the ALARMS push-button is operated, the display of the selected
control card provides an indication of that card's level and type (rising
or falling) of each alarm level (A1, A2, A3, STEL, LTEL).
If the Engineering Key is fitted to the Engineering Card, adjustments
can be made to the alarm levels, within pre-defined limits, and additional
test facilities become available. This facility allows each alarm operation
to be checked and, if required, its associated output relay to be
exercised.
3.3.9 SIGNAL Push-button
When the SIGNAL push-button is operated, the display of the selected
control card provides an indication of that cards sensor signal as
follows:
a. 4 - 20mA Control Card - Loop current in mA.
b. Catalytic Control Card - Catalytic bridge output (sensitivity) in mV.
3.3.10 ZERO Push-button
The ZERO push-button can only be used when the Engineering Key is
fitted to the Engineering Card and is used to calibrate the zero point of
the selected control card.
3.3.11 SPAN Push-button
The SPAN push-button can only be used when the Engineering Key is
fitted to the Engineering Card and is used to calibrate the span point of
the selected control card.
3.3.12 1ST SPAN Push-button
The 1ST SPAN push-button can only be used when the Engineering
Key is fitted to the Engineering Card and is used to calibrate the span
point of a new catalytic sensor fitted to a selected catalytic control
card.
This function is used to provide an indication, in conjunction with
subsequent normal span adjustments, of the output sensitivity of a
catalytic sensor and to automatically indicate poisoning or loss of
sensor performance.
3.3.13 CLOCK Push-button
When the CLOCK push-button is operated, the display of the selected
control card provides an indication of the time and date of the rack
clock.
