3BHE033068P106邏輯順序卡件
還應考慮驅動軸的縱向膨脹。自從這種膨脹通常由花鍵承擔，這些花鍵也必須進行潤滑。癥狀是：
信號的不穩定性，例如在慢速運行期間信號的跳躍。
6.5稱重傳感器、接線盒和裝電線
稱重傳感器非常堅固，能夠承受高過載。壓力傳感器的數據
不會緩慢變化，而是逐步變化，通常與磨機中的事件相關。過分的
過載通常會導致零點永久偏移。
接線盒接觸不良會導致間歇性故障。靈敏度和零點都可能變化。
檢查所有螺釘端子。不要使用壓接至連接線的針腳，因?yàn)檫@些針腳通常有效過了一段時間就松了。
電纜，尤其是稱重傳感器的電纜，是最容易受到損壞的部分。
由于稱重傳感器繞組的電阻較低，因此很容易檢查稱重傳感器和電纜
來自控制單元。
一次繞組的電阻的典型讀數為1Ω，二次繞組的輸出阻抗為1-3Ω。
電纜或稱重傳感器中的絕緣故障可能導致靈敏度不正確或零點不穩定。
當稱重傳感器電路在可斷開端子處與接地和控制單元隔離時，很容易測量與控制單元的絕緣。
如果電纜布線不正確，可能會受到其他電纜的干擾。
有關電路圖應用，請參閱適用控制單元的手冊：
帶Millmate控制器400的Millmate帶鋼張力系統，3BSE023139Rxxxx
帶張力電子裝置PFEA 111/112、3BSE029380Rxxxx的卷筒紙張力系統
帶張力電子裝置PFEA 113、3BSE029382Rxxxx的卷筒紙張力系統
幫助建立一個更安全的世界
確保您在之前閱讀并理解這些說明
操作設備。
請?zhí)貏e注意安全警告。
警告
本手冊涵蓋的設備項目包括：
1.未設計或認證用于危險區域。
2.僅設計用于室內使用。
3.不得暴露在雨水或濕氣中。
警告
1.僅在5701控制裝置中使用經批準的零件和附件系統
2.維護安全標準，定期維護、校準和由合格人員操作5701控制系統：
本質的
重要通知
1.齊薇格分析有限公司不承擔安裝責任
和/或使用其設備，如果未按照手冊的適當發行和/或修訂。
2.本手冊的用戶應確保其在所有方面都是適當?shù)?br/>
待安裝和/或操作的確切設備的詳細信息。如果在
如有疑問，用戶應聯系Zellweger Analytics Limited尋求建議。
Longitudinal expansion of the drive shaft should also be taken into account. Since
such expansion is often taken up by splines, these must also be lubricated. The symptoms are
instability of the signal, for instance jumps in the signal during slow running.
6.5 Fault Tracing of Load Cells, Junction Boxes and
wiring
The load cell is very robust and can withstand high overloads. The data of a Pressductor load cell
does not change slowly, but in steps, usually in connection with an event in the mill. Excessive
overloading usually results in permanent shifting of the zero point.
Poor contact in the junction box causes intermittent faults. Both sensitivity and zero point may vary.
Check all screw terminals. Do not use pins crimped to the connecting wires, as these often work
loose after a time.
The cabling, especially the cable to the load cell, is the part that is most exposed to damage.
Since the resistance of the load cell windings is low, it is easy to check the load cells and cabling
from the control unit.
Typical readings are 1 Ω for the resistance of the primary winding and 1-3 Ω for the output impedance of the secondary winding.
Insulation faults in the cabling or the load cell may cause incorrect sensitivity or unstable zero point.
When the load cell circuits have been isolated from earth and from the control unit at the disconnectable terminals, it is easy to measure the insulation from the control unit.
If the cables are not routed correctly, they may pick up interference from other cables.
For circuit diagram applications, see the manual for the applicable control unit:
Millmate Strip Tension Systems with Millmate Controller 400, 3BSE023139Rxxxx
Web Tension Systems with Tension Electronics PFEA 111/112, 3BSE029380Rxxxx
Web Tension Systems with Tension Electronics PFEA 113, 3BSE029382Rxxxx
Helping to make a safer world
Ensure that you read and understand these instructions BEFORE
operating the equipment.
Please pay particular attention to the Safety Warnings.
WARNINGS
The items of equipment covered by this manual are:
1. Not designed or certified for use in hazardous areas.
2. Designed for indoor use only.
3. Not to be exposed to rain or moisture.
CAUTIONS
1. Use only approved parts and accessories with the 5701 Control
System.
2. To maintain safety standards, regular maintenance, calibration and
operation of the 5701 Control System by qualified personnel is
essential.
IMPORTANT NOTICES
1. Zellweger Analytics Limited can take no responsibility for installation
and/or use of its equipment if this is not done in accordance with the
appropriate issue and/or amendment of the manual.
