PM860K01處理器模塊,3BSE018100R1參數說明
支持10BASE～T和100BASE-TX以太網外設，對其他標準以太網解決方案有良好的兼容性和通用性PCB布局方面，精度為1％的電阻和100 nF的去耦電容應靠近PHY器件放置，并通過最短的路徑到電源。兩對差分信號(TD和RD)應平行走線，避免短截，且盡量保證長度匹配，這樣可以避免共模噪聲和EMI輻射。理想情況下，信號線上不應有交叉或者通孔，同時，差分線應盡可能走在一面。本模塊設計結構，
PM860K01處理器模塊從功能上可以設計成兩種工作模式：Modbus TCP從站模式，Modbus TCP主站模式。Modbus TCP從站模式，是把以太網總線Modbus TCP請求轉化成串口總線Modbus RTU請求，也就是以太網設備從PLC讀出數據；Modbus TCP主站模式，是把串口總線Modbus RTU請求轉化成以太網Modbus TCP請求，也就是PLC從以太網設備讀入數據。下面以Modbus TCP從站模式為例。撥碼功能配置表模塊配置主要是通過8位撥碼開關實現，通過這撥碼開關配置模塊的工作模式，以太網IP地址，串口RTU地址，波特率。驅動開發包括兩部份：芯片物理層驅動(MAC，PHY)和TCP/IP協議層驅動。芯片物理層驅動主要是對LPC1758的以太網控制器和PHY芯片的初始化和控制輸入輸出的函數化打包，以便供TCP/IP協議層驅動調用。TCP/IP協議層驅動開發需要參考TCP/IP標準協議Modbus TCP與西門子PLC數據地址對應關系
BCNet-S7PPI、BCNet-S7MPI內部集成ModbusTCP服務器，支持ModbusTCP通訊的客戶機軟件可以直接讀寫PLC的數據。實現功能號包括：FC1、FC2、FC3、FC4、FC5、FC6和FC16。
PLC的站地址為Modbus從站地址。
PLC的數據區和Modbus數據區在BCNet-S7PPI/MPI內部被自動映射，PLC內不需要編寫通訊程序：
1． PLC的Q區對應Modbus的線圈，Q0.0對應00001。
2． PLC的I區對應Modbus的離散輸入，I0.0對應10001。
3． PLC的M區對應Modbus的輸入寄存器，MW0對應30001。
4． PLC的V區(DB區)對應Modbus的乘法寄存器，VW0對應40001?，F(xiàn)場安裝了K4-2*73NO28F型離心式通風機兩臺，配套電機YR1250-10/1430異步電動機，功率1250KW,定子電壓6KV,電流145A,轉子電壓801V,電流935A,采用轉子回路串接頻敏變阻器降壓?jiǎn)?dòng)方式。電控系統采用繼電器、接觸器組成的模擬控制系統，就地按鈕控制，致使風機各輔助設備包括潤滑站、立風門、平風門、反風門、冷卻水泵等的控制設備布置分散，未實現集中控制。
Strengthen the staff operation specification of device and plate welding tooling;
5. The "module coaxial inspection pin" is used to inspect the coaxiality of the shell and the device, which replaces the jumper to inspect the module, reducing the effect on the module and reducing the pollution and damage to the device core. There are many things worth learning about industrial switches. Here we mainly introduce how to avoid packet loss in energy data control of Gigabit industrial switches. Flow control can not improve the data throughput of the whole industrial switch, but it can avoid packet loss in the industrial switch.
The Gigabit Ethernet physical layer protocol IEEE defines several Gigabit Ethernet interfaces for different physical media, including 1000base CX, 1000base SX, 1000base LX and 1000base-t.
Among them, 1000base CX is the interface used for 155 Ω balanced coaxial cable. In practice, there is no real product. 1000BASE-T is the interface that can be used for class 5 or higher twisted pair, and its standard is IEEE802 3 AB, this standard was just released in June 1999, and now commercial products have just been launched in the market.
1000base SX
