CI801通訊模塊
用塞尺檢測點2出動、靜鐵芯間隙A（0.33mm-0.35mm）（0.33mm塞尺通過，0.36mm塞尺不通過）（如檢測點示意圖）,若不符合要求，松開螺母Ⅳ，微調螺栓Ⅲ（太大，順時針擰緊螺栓Ⅲ；太小，逆時針?biāo)砷_螺栓Ⅲ）使動靜盤間隙滿足要求，鎖緊螺母Ⅳ（如調整示意圖）。
c)用塞尺復檢動靜盤間隙，反復調整至滿足要求為止，并保證間隙均勻。
d)用塞尺檢測點3、點4處動靜盤間隙偏差≤0.1mm。
1.2 手動松閘調整
CI801通訊模塊a) 推動手柄，檢查手柄左、右擺動自由行程為18-28mm，若不符合要求，松開螺釘M5X10和墊圈5；擰下螺母M10（兩件，靠外側）和墊圈10，再卸下調整杠桿和復位簧；調整螺母M10（緊貼手柄）（太大，順時針擰緊螺母M10；太小，逆時針?biāo)砷_螺母M10），滿足手柄左右擺動自由行程的要求。
b) 裝上復位簧與調整杠桿，用螺母M10涂上可賽新1243螺紋膠連同墊圈10將調整杠桿固定于件推拉桿上，在螺釘M5X10對應螺孔涂上可賽新1243螺紋膠，用螺釘M5X20連同墊圈5將調整杠桿緊固。再將螺母M10涂上可賽新1243螺紋膠鎖緊。
1.3 制動器噪音調整
a) 用扳手（10mm）擰松螺母M6，用內六角扳手（3mm）順時針擰緊螺栓M6，大約擰過角度為60°。
b) 用相同的方法調整其他的3個螺栓。
c) 復檢制動器的運行噪音，如還是不符合要求，重復以上步驟。
d) 保證制動器的啟動電壓不超額定電壓的80%。
e) 用扳手（10mm）鎖緊螺母M6，在螺栓和螺母處用紅漆封固。
1.4 制動器微動開關的調整
a)用扳手（7mm）擰松鎖緊螺母M4和螺栓M4X50。
b) 涂適量樂泰271在螺栓上。
c) 用扳手（7mm）非常緩慢的調整螺栓M4X50，當聽到開關動作的聲音的時候停止。required for communication interaction and the communication refresh speed. Huichuan PLC is equipped with four wiring terminals, which can be used for Modbus communication. The program does not need to write the time-division scanning program, and the PLC will automatically execute in the background in time-division. COM0 port only supports MODBUS slave station, and jp0 jumper needs to be unplugged when using COM0 port as slave station, because the default port is PS / 2 port of mouse head, The supported protocols are man-machine monitoring protocol and download protocol, so normal communication can be realized only after power on again. COM1 port can support MODBUS master station and slave station, and XP PLC com2 port can also support MODBUS master station and slave station. The maintenance control touch screen has complete functions, reliability and durability, and simple programming. Compared with other HMI products, it has friendly interface and brings great convenience to user programming and maintenance. With the development of industrial automation, the solution of maintenance control touch screen supporting PLC, single chip microcomputer and PC automation system is becoming more and more popular. Maintenance control touch screen is a dazzling star in man-machine interface.
