UAD206A101產品顏色,ABB卡件
電纜和卡邊緣連接器CONFlGURATlONVMIVME-2511設計用于通過兩根扁平帶狀電纜接收觸點輸入連接至連接器P3和P4，如圖5-4所示。導線#1如圖所示由于P3和P4的插腳#1，連接器插入收割臺時的底部如圖所示安裝。使用以C行作為末端電路的扁平帶狀連接器，所有奇數由于P3和P4的C行為連接至VMEbus接地。因此，電纜的所有偶數編號導線是進入VMIVME-2511的觸點輸入信號。如果電纜連接器使用A行作為終端電路時，所有奇數編號的導線都是信號導線，而偶數編號的導線將接地。
UAD206A101產品顏色表5-2和5-3顯示了64VMIVME-2511的輸入通道。電纜導體/信號分配將取決于選擇的電纜連接器類型（A行或C行作為終端電路）。VMIVME-2511的兼容電纜連接器是Panduit#I 20-964-455E。應變消除為Panduit#100-000-032。標題連接器15，Panduit#I 20-964-053A，焊接至P.C.板維護技術手冊的本節提供了與VMIC產品的維護和保養。如果產品出現故障用戶應驗證以下內容：a、 軟件b、 系統配置c、 電氣連接d、 跳線或配置選項e、 電路板完全插入其正確的連接器位置f、 連接器引腳清潔且無接觸g、 相鄰板的任何組件均不受干擾；插入或從VMEbus卡czge卸下電路板h、 電纜和輸入/輸出連接的質量不建議進行用戶級維修。6.2維護打印附錄A包含供參考的圖紙和圖表。6.3保修VMIC的標準產品保證不存在以下缺陷：材料和工藝有效期為自簽署之日起兩年（24個月）
運輸為解除本保修，VMlC同意在以下時間進行維修或更換：VMIC的設施以及由VMIC自行決定的任何零件、組件、子組件附件或任何硬件、軟件或系統產品正常使用證明材料和工藝有缺陷?？蛻魬?yīng)在客戶發現此類缺陷一周后。為了退回有缺陷的產品或零件，費用由VMIC承擔客戶必須聯系VMIC的客戶服務部門以獲取電車票號碼。在獲得電話號碼后，產品或零件
110 CABLE AND CARD-EDGE CONNECTOR CONFlGURATlON
The VMIVME-2511 is designed to receive contact inputs via two flat ribbon cables
connected to connectors P3 and P4 as shown in Figure 5-4. Conductor #1 is shown at
the bottom of the connector as it plugs into the header, due to pin #1 of P3 and P4
being mounted as shown.
Using a flat ribbon connector that has Row C as the end circuit, all of the odd
numbered conductors of the cable are grounded due to Row C of P3 and P4 being
connected to VMEbus ground. Therefore, all even numbered conductors of the cable
are contact input signals coming into the VMIVME-2511. If a cable connector were
used that has Row A as the end circuit, all odd numbered conductors would be signal
conductors, while the even numbered conductors would be ground.
Tables 5-2 and 5-3 shows the P3 and P4 connector pin assignment for the 64
input channels of the VMIVME-2511. Cable conductor/signal assignment will depend
on the type of cable connector chosen (Row A or Row C as end circuit).
A compatible cable connector for the VMIVME-2511 is Panduit #I 20-964-455E.
Strain relief is Panduit #100-000-032. Header connector 15, Panduit #I 20-964-053A,
is soldered to the P.C. BoardMAINTENANCE
This section of the technical manual provides information relative to the
care and maintenance of VMIC's products. Should the products malfunction, the
user should verify the following:
a. Software
b. System configuration
c. Electrical connections
d. Jumper or configuration options
e. Boards fully inserted into their proper connector location
f. Connector pins are clean and free from contamimtisn
g. No components of adjacent boards are disturbed wher; inserting or
removing the board from the VMEbus card czge
h. Quality of cables and I/O connections
User level repairs are not recommended. Contact factory for a Return
Authorization Number.
6.2 MAINTENANCE PRINTS
Appendix A contains drawings and diagrams for reference purposes.
6.3 WARRANTY
VMIC's Standard Products are warranted to be free from defects in
material and workmanship for a period of two years (24 months) from the date of
shipment. In discharge of this warranty, VMlC agrees to either repair or replace, at
VMIC's facility and at VMIC's discretion, any part, component, subassembly
accessory, or any hardware, software or system product, which under proper and
normal use proves defective in material and workmanship.
The customer shall provide notice to VMlC of each such defect within
one week after the customer's discovery of such defect.
In order to return the defective product or part at VMIC's expense, the
customer must contact VMIC's Customer Service Department to obtain a Call
Ticket Number. After a Call Ticket Number has been obtained, the product or part
