3BSE069274R1使用區域,ABB觸摸屏
信號調節輸入濾波器終端選項：該板可以與多種輸入信號調節濾波器電路。用于差速器輸入時，電路由串聯電阻器和連接在信號輸入端的電容器（參見圖3）；然而，對于單端輸入，輸入
電路可以跨接以提供輸入去抖動過濾器（請參閱訂購選項）。絕對最大輸入電壓：±60 V持續
通用規范摘要輸入/輸出端口數：四個（每個端口8位）輸入/輸出控制：每個端口單獨可通過跳線或以下方式選擇輸入或輸出軟件控制內置測試功能
3BSE069274R1使用區域該板的設計具有內部自檢邏輯。CMOS緩沖器連接直接向輸入端輸出數據寄存器（ODR）用于生成比較器偏移的電壓比較器可用于離線操作期間的健康測試。VMIVME-2534還支持實時測試輸出驅動器和/或輸入電壓比較器故障檢測和隔離到板/位級別?？刂坪蜖顟B(tài)寄存器（CSR）：一個CSR是用于控制前面板故障LED和內部內置測試功能。故障指示燈：提供一個前面板故障指示燈可以在程序控制下打開和關閉。這LED在通電和系統復位時點亮。物理/環境溫度范圍：0至55°C，工作20至85°C，儲存相對濕度范圍：20%至80%，非冷凝冷卻：對流功率要求：最大2.1 A時：+5 V應用程序-繼電器驅動器燈驅動器電磁閥驅動器液壓錘驅動器步進電機驅動器雙向可控硅驅動器LED驅動器高電流、高壓驅動器光纖LED驅動器正/負真實訂購信息-此電路板可與訂購正或負真輸出選項。數據轉換（反演）由輸出數據的選擇決定閂鎖。正真輸出選項導致VMEbus邏輯一個用于打開相應的輸出晶體管，其中為用戶提供零電壓。
Signal Conditioning Input Filter Terminator
Option: The board may be ordered with a variety of
input signal conditioning filter circuits. For differential
inputs, the circuit consists of a series resistor and
capacitor connected across the signal input (see
Figure 3); whereas, for single-ended inputs, the input
circuit can be jumpered to provide an input debounce
filter (see the Ordering Options).
Absolute Maximum Input Voltage: ±60 V sustained
GENERAL SPECIFICATION SUMMARY
Number of I/O Ports: Four (8 bits per port)
Input/Output Control: Each port is individually
selectable to be input or output via jumpers or under
software controBuilt-in-Test Features: This board is designed with
internal self-test logic. CMOS buffers connect the
Output Data Registers (ODRs) directly to the input
voltage comparators to generate comparator offsets that
may be used as a health test during off-line operation.
The VMIVME-2534 also supports real-time testing of
output drivers and/or input voltage comparators for
fault detection and isolation to the board/bit level.
Control and Status Register (CSR): One CSR is
provided to control the front panel Fail LED and
internal Built-in-Test features.
Fail LED: A front panel Fail LED is provided which
can be turned ON and OFF under program control. This
LED is illuminated at power on and system reset.
PHYSICAL/ENVIRONMENTAL
Temperature Range: 0 to 55 °C, operating
-20 to 85 °C, storage
Relative Humidity Range: 20 to 80 percent,
noncondensing
Cooling: Convection
Power Requirements: +5 V at 2.1 A maximum
APPLICATIONS —
Relay drivers
Lamp drivers
Solenoid drivers
Hammer drivers
Stepper motor drivers
Triac drivers
LED drivers
High-current, high-voltage drivers
Fiber-optic LED driversPOSITIVE/NEGATIVE TRUE ORDERING
INFORMATION — This board may be ordered with
positive or negative true output options. The data conversion
(inversion) is determined by the selection of output data
latches.
A positive true output option causes a VMEbus logical
one to turn the corresponding output transistor ON, which
supplies the user with zero volts.
