1VCR007346 G0012操作觸摸屏,ABB使用配置手冊
用于在PAC系統中使用模擬擴展器時的故障報告RX7i機架，當基座位于插槽4和擴展器位于插槽11中。在這種情況下，出現故障的擴展器始終顯示為插槽2，電路號將根據擴展器使用的插槽顯示，如下表。顯示每個通道的輸入/輸出參考地址如果用戶將硬件配置存儲到閃存，則表示“邏輯/配置電源”設置為“始終閃爍”或“有條件”Flash”，然后在編程軟件時，硬件配置將不相等不會驗證為相等。
1VCR007346 G0012操作觸摸屏控制器和IO故障表可能需要清除兩次以清除故障狀態需要清除控制器和IO故障表以占用CPU退出停止/故障模式。如果其中一個表包含重復出現的故障，則清除表格的順序可能很重要。如果CPU是清除兩個表后，仍處于停止/故障模式，請嘗試清除故障表。
當使用使用以下命令的VME內存區域啟用塊傳輸時，使用程序類型AM代碼的VME模塊程序類型AM代碼之一，Rx7i CPU有時會生成訪問相關VME的塊傳輸（BLT和MBLT）循環記憶力因此，如果您將VME內存區域配置為使用程序類型AM代碼之一（AM代碼3Ah、3Eh、0Ah或0Eh），請確保遵守以下兩條規則中的至少一條：a） 內存區域的接口類型參數不得設置為“Qword訪問（64位）”，并且VME塊傳輸參數必須設置為“禁用”。
-ORb）系統可能不包含任何“程序”和“數據”VME內存VME地址重疊的區域。（如果有多個VME如果模塊響應BLT或MBLT循環，則可能會出現系統錯誤結果。）一旦強制開啟或強制關閉存儲到PLC，用戶就無法通過下載直接從強制打開切換到強制關閉，反之亦然初始值。用戶可以通過下載關閉強制，然后然后通過另一次下載更改力的開啟或關閉。
For fault reporting when an analog expander is used in a PACSystems
RX7i rack, a special case exists when the base is in slot 4 and an
expander is present in slot 11. In this case, the slot number for a faulty
expander is always displayed as slot 2, and the circuit number will
display according to the slot used for the expander, as shown in the
following table. The I/O reference address for each channel is displayed
as blankIf the user stores a hardware configuration to flash which indicates that
“Logic/Config Power up Source” is set to “Always Flash” or “Conditional
Flash” and then subsequently changes the name of the target in the
programming software, the hardware configuration will go Not Equal and
will not Verify as equal.
Controller and IO fault tables may need to be
cleared twice to clear faulted state
Both Controller and IO fault tables need to be cleared to take the CPU
out of Stop/Fault mode. If one of the tables contains a recurring fault, the
order in which the tables are cleared may be significant. If the CPU is
still in Stop/Fault mode after both tables are cleared, try clearing the fault
tables again.
VME modules using program type AM codes When Block Transfers are enabled with a VME memory region that uses
one of the program type AM Codes, the Rx7i CPU sometimes generates
block transfer (BLT & MBLT) cycles to access the associated VME
memory. Therefore, if you have a VME memory region configured to use
one of the program type AM Codes (AM Codes 3Ah, 3Eh, 0Ah, or 0Eh),
be sure to follow at least one of these two rules:
a) The memory region's Interface Type parameter must not be set to
"Qword Access (64-bit)", and the VME Block Transfer parameter must
be set to "Disabled".
-ORb) The system may not contain any "program" and "data" VME memory
regions with overlapping VME addresses. (If more than one VME
module were to respond to a BLT or MBLT cycle, a system error could
result.)Once a force on or force off has been stored to the PLC, the user cannot
switch from force on to force off or vice-versa directly by downloading
initial values. The user can turn off the force by doing a download, and
then change the force on or off by another download.
