T1023-07C監測模塊,ABB配置說明
如果使用NIOT調試器命令，則需要保存在偏移范圍$00001000到$000016F7的某處。這個NIOT參數的大小不超過128字節。此環境的設置指針確定其位置。如果您已將相同的空間用于如果您擁有程序信息或命令，它們將被覆蓋并丟失。您可以在此中重新定位網絡接口配置參數通過使用ENV命令更改網絡自動引導配置參數從默認值$00001000偏移到您需要清除NVRAM中的數據。默認結束地址是本地內存的計算大小。
T1023-07C監測模塊如果內存開始從$00000000更改，該值也需要待調整。以納秒為單位的DRAM速度=60？此參數的默認設置將根據速度而變化安裝在電路板上的DRAM內存部件。默認設置達到可用DRAM內存庫中的最低速度。ROM第一次訪問長度（0-31）=10？這是編程到MPC105“ROMFAL”字段中的值（內存控制配置寄存器8：位23-27）以指示訪問ROM時使用的時鐘周期數。最低允許的ROMFAL設置為$00；允許的最高價格為1美元。這個輸入的值取決于處理器速度；請參閱中列出的處理器/內存夾層模塊用戶手冊附錄D，相關文件，以獲取適當?shù)闹?。這個默認值根據系統的總線時鐘速度而變化。注：ROM首次訪問長度不適用于MVME2600/3600/4600。配置值被忽略PPCBug。
ROM下一個訪問長度（0-15）=0？編程到MPC105“ROMNAL”字段中的值（存儲器控制配置寄存器8：位28-31），表示等待狀態半字節（或突發）模式ROM訪問的訪問時間。最低的允許的ROMNAL設置為$0；允許的最高金額為$F輸入的值取決于處理器速度；參考您的
理器/內存夾層模塊用戶手冊價值觀默認值根據系統的總線時鐘而變化速度注：ROM下一個訪問長度不適用于MVME2600/MVME3600/MVME4600。配置值為被PPCBug忽略。初始化中的PIRQx（PCI中斷）路由控制寄存器IBC（PCI/ISA總線橋控制器）。ENV參數是32位的值除以4得到路線控制值寄存器PIRQ0/1/2/3。默認值由系統類型決定。對于PCI/ISA中斷分配和建議值的詳細信息輸入此參數，請參閱MVME2600程序員參考指南，見附錄D，相關文件。配置VMEbus接ENV提出了以下一系列問題來設置VMEbus接口適用于MVME2300/MVME2600/MVME3600/MVME4600系列模塊。要執行此配置，您應該有一個程序員手冊中描述的通用ASIC知識參考指南。
If you use the NIOT debugger command, these parameters need to be
saved somewhere in the offset range $00001000 through $000016F7. The
NIOT parameters do not exceed 128 bytes in size. The setting of this ENV
pointer determines their location. If you have used the same space for your
own program information or commands, they will be overwritten and lost.
You can relocate the network interface configuration parameters in this
space by using the ENV command to change the Network Auto Boot
Configuration Parameters Offset from its default of $00001000 to the
value you need to be clear of your data within NVRAM.
The default Ending Address is the calculated size of local memory. If
the memory start is changed from $00000000, this value will also need
to be adjusted.
DRAM Speed in NANO Seconds = 60?
The default setting for this parameter will vary depending on the speed
of the DRAM memory parts installed on the board. The default is set
to the slowest speed found on the available banks of DRAM memory.
ROM First Access Length (0 - 31) = 10?
This is the value programmed into the MPC105 “ROMFAL” field
(Memory Control Configuration Register 8: bits 23-27) to indicate the
number of clock cycles used in accessing the ROM. The lowest
allowable ROMFAL setting is $00; the highest allowable is $1F. The
value to enter depends on processor speed; refer to yourProcessor/Memory Mezzanine Module User’s Manual, listed in
Appendix D, Related Documentation, for appropriate values. The
default value varies according to the system’s bus clock speed.
Note ROM First Access Length is not applicable to the
MVME2600/3600/4600. The configured value is ignored by
PPCBug.
ROM Next Access Length (0 - 15) = 0?
The value programmed into the MPC105 “ROMNAL” field (Memory
Control Configuration Register 8: bits 28-31) to represent wait states
in access time for nibble (or burst) mode ROM accesses. The lowest
allowable ROMNAL setting is $0; the highest allowable is $F. The
value to enter depends on processor speed; refer to your
Processor/Memory Mezzanine Module User’s Manual for appropriate
values. The default value varies according to the system’s bus clock
speed.
Note ROM Next Access Length is not applicable to the
MVME2600/MVME3600/MVME4600. The configured value is
ignored by PPCBug.Initializes the PIRQx (PCI Interrupts) route control registers in the
IBC (PCI/ISA bus bridge controller). The ENV parameter is a 32-bit
value that is divided by four to yield the values for route control
registers PIRQ0/1/2/3. The default is determined by system type. For
details on PCI/ISA interrupt assignments and for suggested values to
enter for this parameter, refer to the 8259 Interrupts section of the
MVME2600 Programmer’s Reference Guide, listed in Appendix D,
Related Documentation.
Configuring the VMEbus Interface
ENV asks the following series of questions to set up the VMEbus interface
for the MVME2300/MVME2600/MVME3600 /MVME4600 series
modules. To perform this configuration, you should have a working
knowledge of the Universe ASIC as described in the Programmer’s
Reference Guide.
