HIEE451116R0001機器人卡件,ABB使用在哪里
ISA超級輸入/輸出設備（ISASIO）MVME2603/2604使用National的PC87308 ISASIO芯片半導體來實現P2和前面板的某些部分輸入/輸出：
? 兩個異步串行端口（COM1和COM2）通過P2和過渡模塊
? 通過P2和轉換模塊的并行端口：–MVME712M兼容機型中的Centronics打印機端口–兼容MVME761的IEEE1284雙向并行端口模型
? 通過驅動器/電源連接器J4支持軟盤驅動器
HIEE451116R0001機器人卡件? 通過圓形DIN連接器J6和J8異步串行端口ISASIO設備提供的兩個異步端口采用通過EIA-232-D驅動器緩沖的TTL電平信號和接收器并路由到P2連接器。
硬件使用ISA將兩個串行端口初始化為COM1和COM2輸入/輸出基址分別為3F8美元和2F8美元。此默認值配置還將COM1分配給PIB（PCI/ISA網橋控制器）中斷請求行IRQ4和COM2至IRQ3。您可以更改通過重新編程ISASIO設備進行默認配置。有關詳細信息編程信息，請參閱MVME2603/2604程序員參考指南，見附錄D，相關文件，以及ISASIO的供應商文件裝置并行端口
并行端口是MVME712M兼容機型中的Centronics打印機接口，以及中的完整IEEE1284雙向并行端口MVME761兼容型號。這兩個版本都使用ISASIO設備。所有并行輸入/輸出接口信號通過
串聯阻尼電阻器。硬件使用ISA IO基址將并行端口初始化為PPT130億美元。此默認配置還將并行端口分配給PIB（PCI/ISA網橋控制器）中斷請求線IRQ7。你可以改變通過重新編程ISASIO設備的默認配置。對于詳細編程信息，請參閱PCI和ISA總線MVME2603/2604程序員參考指南中的討論，附錄D相關文件中列出，并發送給供應商ISASIO設備的文檔。
ISA Super I/O Device (ISASIO)
The MVME2603/2604 uses a PC87308 ISASIO chip from National
Semiconductor to implement certain segments of the P2 and front-panel
I/O:
? Two asynchronous serial ports (COM1 and COM2) via P2 and
transition module
? Parallel port via P2 and transition module:
– Centronics printer port in MVME712M-compatible models
– IEEE1284 bidirectional parallel port in MVME761-compatible
models
? Floppy disk drive support via drive/power connector J4
? Keyboard and mouse interface via circular DIN connectors J6 and
J8Asynchronous Serial Ports
The two asynchronous ports provided by the ISASIO device employ
TTL-level signals that are buffered through EIA-232-D drivers and
receivers and routed to the P2 connector.
Hardware initializes the two serial ports as COM1 and COM2 with ISA
I/O base addresses of $3F8 and $2F8 respectively. This default
configuration also assigns COM1 to PIB (PCI/ISA Bridge Controller)
interrupt request line IRQ4 and COM2 to IRQ3. You can change the
default configuration by reprogramming the ISASIO device. For detailed
programming information, refer to the PCI and ISA bus discussions in the
MVME2603/2604 Programmer’s Reference Guide, listed in Appendix D,
Related Documentation, and to the vendor documentation for the ISASIO
device.
Parallel Port
The parallel port is a Centronics printer interface in MVME712Mcompatible models, and a full IEEE1284 bidirectional parallel port in
MVME761-compatible models. Both versions are implemented with the
ISASIO device. All parallel I/O interface signals are routed to P2 through
series damping resistors.
Hardware initializes the parallel port as PPT1 with an ISA IO base address
of $3BC. This default configuration also assigns the parallel port to PIB
(PCI/ISA Bridge Controller) interrupt request line IRQ7. You can change
the default configuration by reprogramming the ISASIO device. For
detailed programming information, refer to the PCI and ISA bus
discussions in the MVME2603/2604 Programmer’s Reference Guide,
listed in Appendix D, Related Documentation, and to the vendor
documentation for the ISASIO device.
