PP836觸摸屏,PP836使用配置說明
Genius手持式監視器可用于顯示GBC總線地址及其軟件版本，以及為全局?jǐn)?shù)據配置的系列六寄存器地址。HHM版本IC660HHM501H（修訂版4.5）或更高版本。GBC模塊上沒有手持式監視器連接器，但是，手持式監視器可以在連接到計算機上的任何其他設備時與GBC通信公共汽車?？蛇x地，可以在總線上靠近GBC。手持式編程器GBC可以使用90-30系列手持式編程器（IC693PRG300）進行配置。Genius輸入/輸出塊Genius輸入/輸出塊可以與GBC位于同一總線上。然而，因?yàn)楣财嚳刂破髋c舊的A相塊不兼容，
PP836觸摸屏它們不應安裝在同一塊上Genius總線
Genius總線是一條屏蔽雙絞線，菊花鏈連接在設備之間，終止于兩端。正確的電纜選擇對系統的成功運行至關重要。合適的電纜GEK-90486-1《Genius輸入/輸出系統和通信用戶手冊》中列出了類型。診斷總線上的Genius塊和其他設備自動報告故障、警報和某些其他信息PLC的預定義條件。輸入和故障信息來自區塊31 2 3 4GBC公司F F令牌故障在任何總線掃描期間，只能發送一條診斷消息。如果已經收到故障信息在掃描過程中（由另一個設備發送），設備會將其自己的診斷消息保存到下一個設備可用總線掃描。例如，如果通信令牌當前在設備3上，并且發生故障同時發生在設備3和4上，如果另一個設備發生故障，設備3可以發送其診斷消息消息尚未發送。設備4必須再等待至少一次總線掃描才能發送其診斷信息。GBC存儲其收到的任何診斷消息。它們由Series 90自動讀取30 CPU。然后，可以使用編程軟件在故障表中顯示故障。天才
必須使用手持式監視器從故障表中清除故障。
The Genius Hand-Held Monitor can be used to display the GBC bus address, its software version,
and the Series Six register address configured for global data. HHM version IC660HHM501H
(revision 4.5) or later is required. There is no Hand-Held Monitor connector on the GBC module,
but a Hand-Held Monitor can communicate with the GBC while connected to any other device on
the bus. Optionally, an additional HHM mating connector can be installed on the bus near the
GBC.
Hand-Held Programmer
The GBC can be configured using a Series 90-30 Hand-Held Programmer (IC693PRG300).
Genius I/O Blocks
Genius I/O blocks can be present on the same bus as the GBC. However, because the Bus
Controller is not compatible with older phase A blocks, they should not be installed on the same
bus.
Genius Bus
The Genius bus is a shielded twisted-pair wire, daisy-chained between devices, and terminated at
both ends. Proper cable selection is critical to successful operation of the system. Suitable cable
types are listed in GEK-90486-1, the Genius I/O System and Communications User’s Manual.
Diagnostics
Genius blocks and other devices on the bus automatically report faults, alarms and certain other
predefined conditions to the PLC.
INPUTS AND FAULT MESSAGE
