3BHB003387R0101可控硅卡件,3BHB003387R0101配置教程
這些計數器與PROFIBUS上掃描儀的整體操作有關。
以下是一般計數器統計信息列表：
?ErrLanOffline計數器，寄存器本地：插槽：S.Data[05]。0-7，當LAN遇到錯誤并脫機
?DiagConf計數器register Local:Slot:S.Data[06]統計總確認數，即，對該站生成的郵件的良好回復
?DiagInd計數器，寄存器Local：Slot：S.Data[07]，統計總指示，即，發送到此電臺的未經請求的消息
?ErrNotOk計數器寄存器Local：Slot：S.Data[08]統計總的Not OK確認和指示，即總的錯誤回復和錯誤的主動消息（指示）
3BHB003387R0101?掃描儀存儲瞬時令牌保持時間，單位為Tbits，單位為DiagTokHldTime，注冊本地：插槽：S.Data[09]（LSW）和本地：插槽：S.Data[10]（MSW）。這是掃描儀獲取令牌時發送消息的可用時間。
?掃描儀存儲最小實際令牌保持時間，單位為Tbits，單位為Diagmentokhldtime，寄存器本地：插槽：S.Data[11]（LSW）和本地：插槽：S、 數據【12】（MSW）。此時間是diagTokHldTime的最小值。
如果此數字為0，則可能需要增加目標令牌輪換配置中的時間。
要增加目標令牌旋轉時間，請執行以下操作：
1、在配置工具中打開DP主配置。選擇并突出顯示PROFIBUS。DP。
3、單擊鼠標右鍵，然后從顯示的快捷菜單中選擇“屬性”。
4、在網絡對話框中選擇定時選項卡。
5、選中代幣輪換時間復選框。
6、在中輸入新值（所有主機或活動站的令牌旋轉時間之和）令牌旋轉時間字段。
These counters relate to the overall operation of the scanner on PROFIBUS.
The following is a list of general counter statistics:
?
The ErrLanOffline counter, register Local:Slot:S.Data[05].0-7, increments when the LAN
encounters errors and goes offline
?
The DiagConf counter, register Local:Slot:S.Data[06], counts total confirmations, that is,
good replies to messages that this station has generated
?
The DiagInd counter, register Local:Slot:S.Data[07], counts total indications, that is,
unsolicited messages to this station
?
The ErrNotOk counter, register Local:Slot:S.Data[08], counts the Total Not OK
confirmations and indications, that is, total bad replies and bad unsolicited messages
(indications)
?
The scanner stores the instantaneous token hold time, in Tbits, in DiagTokHldTime,
registers Local:Slot:S.Data[09](LSW) and Local:Slot:S.Data[10](MSW). This is the
time available to send messages when the scanner gets the token.
?
The scanner stores the minimum actual token hold time, in Tbits, in
DiagMinTokHldTime, registers Local:Slot:S.Data[11](LSW) and Local:Slot:
S.Data[12](MSW). This time is the minimum value of diagTokHldTime.
If this number is 0, you may need to increase the target token rotation
time in your configuration.
To increase the target token rotation time, do the following:
1.
Open your DP Master Configuration in the Configuration Tool.
2.
Select and highlight the PROFIBUS.DP.
3.
Right-click and select Properties from the shortcut menu that displays.
4.
Select the Timing tab in the Network Dialog box.
5.
Select the Token Rotation Time checkbox.
6.
Enter the new value (the sum of ALL masters or Active Station’s token rotation time) in
the Token Rotation Time field.
