WOODWARD 9907-077電源模塊
1.產 品 介 紹
品牌：WOODWARD
型號說明：WOODWARD 9907-077電源模塊
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
WOODWARD 9907-077安裝PROFIBUS DP接口CI851/TP851 CI851由處理器單元通過CEX總線供電，因此不需要額外的外部電源。使用以下步驟安裝CI851/TP851：1。將裝置安裝到DIN導軌上，請參見第65頁的“將AC 800M裝置安裝到DIN導軌上”和第78頁的“以單一配置安裝WOODWARD 9907-077處理器裝置”。2.在PROFIBUS DP電纜上安裝連接器。將電纜屏蔽連接到連接器內的接地端子，通過CI581將屏蔽接地。建議使用帶有可切換內置總線終端的連接器。3.將PROFIBUS DP電纜連接到基板上的觸點。4.如果這是在PROFIBUS DP電纜的末端，則打開總線終端。否則，保持總線終端關閉。PROFIBUS DP連接PROFIBUS DP電纜通過位于WOODWARD 9907-077上的9針凹形D型連接器連接。有關現場總線和推薦的認證現場總線設備和組件的安裝，請參閱現場總線文檔和附錄C，推薦組件。PROFIBUS DP必須與屏蔽雙絞線連接
Installing the PROFIBUS DP Interface, WOODWARD 9907-077The CI851 is powered from the processor unit via the CEX-Bus and requires therefore no additional external power source. Use the following procedure to install the CI851/TP851: 1. Mount the unit onto the DIN-rail, see Mounting AC 800M Units onto DIN-Rail on page 65 and Installing the PM86x/TP830 Processor Unit in Single Configuration on page 78.WOODWARD 9907-0772. Install a connector on the PROFIBUS DP cable. Connect the cable screen to the ground terminal within the connector to ground the screen via CI581. A connector with a switchable built-in bus termination is recommended. 3. Connect the PROFIBUS DP cable to the contact on the baseplate. 4. If this is at the end of the PROFIBUS DP cable, switch the bus termination ON. Otherwise leave the bus termination switched OFF. PROFIBUS DP Connection The PROFIBUS DP cable is connected via the 9-pin female D-type connector located on TP851.For installation of the fieldbus and recommended certified fieldbus devices and components, see fieldbus documentation and Appendix C, Recommended Components. The PROFIBUS DP must be connected with shielded twisted pair cablesWOODWARD 9907-077
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.qing-ting.cn
