HIEE-410110-P2工業卡件,ABB卡件
接線板單獨訂購。PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月帶HART IC695ALG628的模擬模塊無熱降額。模塊IC695ALG626在電壓模式下沒有熱降額。電流模式下IC695ALG626的熱降額如圖313所示。分辨率請參閱下面的分辨率和范圍類型表。輸入數據格式可配置為32位字段中的浮點IEEE 32位或16位整數。濾波器選項8Hz、12Hz、16Hz、40Hz、200Hz、500Hz模擬模塊掃描時間（ms）模塊掃描最多可包含四個采集周期。每個周期包括一組特定的通道，如下面的通道掃描部分所述?？倰呙钑r(shí)間取決于掃描中的采集周期數、配置的濾波器選項以及信道是模擬還是HART。HART通信498 HART數據掃描時間（以秒為單位）HART數據掃描可包括多達四個采集周期（類似，但掃描周期、重試次數、插槽變量的啟用/禁用以及直通命令的使用）。如果插槽變量被啟用，更新時間將加倍。HART組中的信道啟用次數：每個HART數據信道每：1 0.7秒更新一次（典型）2 1.9秒（典型值）3 3.0秒（典型）4 4.0秒（通常值）輸入阻抗>100kW電壓輸入電流輸入電阻249W±1%開路檢測時間1秒最大過電壓±60 Vdc連續，最大過電流±28mA連續，50Hz時最大正常模式噪聲抑制（dB）60Hz時8 Hz濾波器85 85 12 Hz濾波器85 86 16 Hz濾波器35 62 40 Hz濾波器3 6 200 Hz濾波器0 0 500 Hz 0 0共模噪聲抑制在50/60 Hz時最小120dB，8 Hz濾波器在50/60赫茲時最小110dB，12 Hz濾波器信道直流串?dāng)_-最小80 dB（單端模式）-最小80分貝（差分模式，接地公共）-60 dB最?。ú罘帜K狀態）。現場狀態LED指示至少一個通道上存在故障或接線板錯誤。TB（接線板）LED指示接線板的存在或不存在。LED由背板電源總線供電。LED狀態指示模塊正常開啟綠色模塊正常并配置為綠色或琥珀色，緩慢閃爍錯誤綠色，快速閃爍模塊正常但未配置PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月帶HART通信500關閉模塊的模擬模塊有故障或無背板電源現場狀態開啟綠色任何已啟用通道無故障，且至少一個通道上存在接線板ON黃色故障斷開接線板不存在或未完全就位TB ON紅色接線板不出現或未完全到位ON綠色接線板存在OFF模塊無背板電源11.2.3配置：ALG626和ALG628 11.2.3.1模塊參數默認描述通道值參考地址%AIxxxxx啟動此模塊的輸入數據的地址。這默認為下一個可用的%AI塊。該數據的格式如第0節所示。信道值參考長度ALG628:16用于此模塊輸入數據的字?jǐn)?shù)。此ALG626:32參數無法更改。診斷參考地址%Ixxxxx通道診斷狀態數據的起始地址。該數據的格式如第11.2.4.2節所示。診斷參考長度0信道診斷數據所需的位參考位數。設置為0時，通道診斷被禁用。要啟用通道診斷映射，請將其更改為非零值。Terminal Blocks are ordered separately. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART IC695ALG628 has no thermal derating. Module IC695ALG626 has no thermal derating in voltage mode. Thermal derating for IC695ALG626 in current mode is shown in Figure 313. Resolution Refer to Resolution and Range Type table below. Input Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field. Filter Options 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, 500Hz Analog Module Scan Time (ms) The module scan can consist of up to four acquisition cycles. Each cycle includes a specific set of channels, as described in the Channel Scanning section below. Total Scan Time depends on the number of acquisition cycles in the scan, the configured filter option, and whether the channels are analog or HART. HART Communications 498 HART Data Scan Time (in seconds) The HART data scan can consist of up to four acquisition cycles (similar but cycles in the scan, number of retries, enabling/disabling of slot variables, and use of Pass-Through commands. If slot variables are enabled, update times are doubled. # Channels in Group Enabled for HART: Each HART Data Channel updates every: 1 0.7 second (typical) 2 1.9 seconds (typical) 3 3.0 seconds (typical) 4 4.0 seconds (typical) Input Impedance >100kW voltage inputs Current Input Resistance 249W ±1% Open Circuit Detection time 1 second maximum Over-voltage ±60 Vdc continuous, maximum Overcurrent ±28mA continuous, maximum Normal Mode Noise Rejection in dB At 50Hz At 60Hz 8 Hz filter 85 85 12 Hz filter 85 85 16 Hz filter 35 62 40 Hz filter 3 6 200 Hz filter 0 0 500 Hz 0 0 Common Mode Noise Rejection 120dB minimum at 50/60 Hz with 8 Hz filter 110dB minimum at 50/60 Hz with 12 Hz filter Channel-Channel DC Crosstalk -80 dB minimum (single ended mode) -80 dB minimum (differential mode, grounded common) -60 dB minimum (differential module status. The Field Status LED indicates the presence of a fault on at least one channel or a terminal block error. The TB (Terminal Block) LED indicates the presence or absence of the terminal block. LEDs are powered from the backplane power bus. LED State Indicates Module OK ON Green Module OK and configured Green or Amber, blinking slowly Error Green, blinking rapidly Module OK but not configured PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART Communications 500 OFF Module is defective or no backplane power present Field Status ON Green No faults on any enabled channel, and Terminal Block is present ON Yellow Fault on at least one channel OFF Terminal block not present or not fully seated TB ON Red Terminal block not present or not fully seated ON Green Terminal block is present OFF No backplane power to module 11.2.3 Configuration: ALG626 and ALG628 11.2.3.1 Module Parameters Parameter Default Description Channel Value Reference Address %AIxxxxx Starting address for the input data of this module. This defaults to the next available %AI block. The format of this data is shown in Section 0. Channel Value Reference Length ALG628: 16 The number of words used for the input data of this module. This ALG626: 32 parameter cannot be changed. Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. The format of this data is shown in Section 11.2.4.2. Diagnostic Reference Length 0 The number of bit reference bits required for the Channel Diagnostics data. When set to 0, Channel Diagnostics is disabled. To enable Channel Diagnostics mapping, change this to a nonzero value.
