FCS01.1E-W0011-A-04-NNBV R911311065工控模塊系統備件
設定最大模擬輸出（20 mA或10V）將最大模擬輸出表示的對象放置在陣列內。按下并松開示教按鈕?，F(xiàn)在，狀態指示器D15每3秒閃爍三次，表示已識別到任何中斷的光束。如果沒有光束中斷，運行模式下的最大模擬輸出值（20 mA或10V）表示沒有光束中斷。4.完成示教要完成示教過程，請按住示教按鈕，直到狀態指示器D15熄滅（約5秒），這表示示教過程結束。設定值保存到非易失性（閃存）存儲器中?；蛘?，短按設定按鈕可以丟棄新設定的值。狀態指示器D15關閉（表示示教過程結束），恢復先前的值。示教過程注意事項：?如果控制器設置為絕對/位置模式（DIP開關S1:2=OFF），則僅當示教區域內的光束中斷時，離散輸出（Out 1）才會改變狀態。例如，如果為射束10設置最小模擬輸出，為射束30設置最大模擬輸出，則僅阻擋射束5或射束40不會改變離散輸出的狀態，而中斷射束20會改變離散輸出狀態。如果光束40和光束20都被阻擋，則離散輸出改變狀態。如果控制器設置為相對/尺寸模式（DIP開關S1:2=ON），如果任何光束中斷，離散輸出（Out 1）將改變狀態。?代替在示教過程中使用要檢測的實際物體，可以在示教期間通過其他手段（例如金屬標志）中斷適當?shù)墓馐?。?-J15引腳列表引腳信號最小值最大值1 I輸出4 mA 20 mA 2 0V DC 3 V輸出0V 10V 4 0V DC表8-模擬板狀態指示器狀態指示器描述狀態含義D15示教指示器關閉示教不活動閃爍示教活動橙色示教過程的最后一步D16模擬輸出狀態關閉V_Out=Off（0V）閃爍啟動（忽略輸出），過電流，或錯誤綠色亮度與模擬輸出成比例重要信息一旦更改，DIP開關設置僅在電源循環后才能識別。
Teach maximum analog output (20 mA or 10V) Place the object that is to be represented by the maximum analog output within the arrays. Press and release the teach button. Status indicator D15 now flashes three times every 3 seconds, which indicates that any interrupted beams have been recognized. If no beams are interrupted, the maximum analog output value (20 mA or 10V) in Run mode indicates that no beams are interrupted. 4. Complete teach To complete the teach process, press and hold the Teach button until the status indicator D15 turns off (approximately 5 seconds), which signals the end of the teach process. The taught values are saved to non-volatile (flash) memory. Alternatively, briefly pressing the Teach button can discard the newly taught values. Status indicator D15 turns off (which indicates the end of the teach process) and the previous values are restored. Notes on the teach process: ? If the controller is set in absolute/position mode (DIP switch S1:2 = OFF), the discrete output (Out 1) changes state only when a beam within the taught area is interrupted. For example, if the minimum analog output is set for beam 10 and the maximum analog output is set for beam 30, blocking only beam 5 or beam 40 does not change the state of the discrete output, while interrupting beam 20 would change the state of the discrete output. The discrete output changes state if both beam 40 AND beam 20 are blocked. If the controller is set in relative/size mode (DIP switch S1:2 = ON), the discrete output (Out 1) changes state if any beam is interrupted. ? Instead of using the actual object to be detected for the teach process, the appropriate beams may be interrupted by other means during the teach process, such as a metal flag. Table 7 - J15 Pin Listings Pin Signal Minimum Maximum 1 I Out 4 mA 20 mA 2 0V DC 3 V Out 0V 10V 4 0V DC Table 8 - Analog Board Status Indicators Status Indicator Description Status Meaning D15 Teach Indicator Off Teach inactive Flashing Teach active Orange Last step of teach process D16 Analog Output Status Off V_out = OFF (0V) Flashing Start up (ignore output), over current, or error Green Brightness proportional to analog output IMPORTANT Once changed, DIP switch settings are only recognized after a power cycle.
