3BSE066485R1輸入控制模塊
特殊處理處理電子電路時，請遵守以下步驟：注意：在處理模塊時，始終使用貝利控制現場靜電套件（零件號1948385_1-包括兩個腕帶、接地線組件、鱷魚夾和靜電消散工作面）。該套件旨在將技術人員和靜電消散工作面連接到同一接地點，以防止靜電放電對模塊造成損壞。1.使用防靜電袋。將模塊放在防靜電袋中，直到準備好將其安裝到系統中。保存包裝以備將來使用。2.打開前的地袋。在打開裝有半導體組件的袋子之前，將其接觸到設備外殼或地面以均衡電荷。3.避免接觸電路。通過邊緣處理組件；避免接觸電路。4.避免半導體的部分連接。使用前，請確認連接到模塊的所有設備均正確接地。5.地面測試設備。6.使用防靜電現場維修真空。必要時清除模塊上的灰塵。7.使用接地腕帶。將腕帶連接到電源輸入面板上的相應接地插頭。電源輸入面板上的接地插頭連接到機柜機箱接地。8.請勿使用鉛筆設置雙列直插式開關。為避免污染油尺開關觸點，從而導致不必要的電路板故障，請勿使用鉛筆設置油尺開關。
引言
本節解釋了在將任何INFI-NET到計算機接口模塊投入運行之前必須做的事情。在操作模塊之前，按照步驟出現的順序閱讀、理解并完成這些步驟。拆箱和檢查1.立即檢查硬件是否有運輸損壞。2.將任何此類損壞通知最近的貝利控制銷售辦事處。3.向處理貨物的運輸公司提出任何損壞索賠。4.使用原包裝材料和容器存放硬件。5.將硬件存放在空氣質量良好、沒有極端溫度和濕度的環境中。INNIS01網絡接口從模塊配置兩個INFI-NET到計算機的接口都需要一個INNIS02網絡接口從模件（NIS）。按如下方式配置NIS模塊。NIS模塊上有四個雙列直插式開關。雙列直插式開關及其功能如下所述。有關雙列直插式開關的位置，請參見圖3-1。此雙列直插式開關設置節點地址。有效節點地址為1到250。請參閱表3-1。第一極是二進制權重為128的MSB位。第八極是二進制加權為1的LSB位。在提供的空間中記錄雙列直插式開關SW1的設置。此雙列直插式開關設置主INFI-NET環路的環路編號。有效回路編號為1到250。參考表3-2。在提供的空間中記錄雙列直插式開關SW2的設置。
SPECIAL HANDLING
Observe these steps when handling electronic circuitry: NOTE: Always use Bailey Controls field static kit (part number 1948385_1 - consisting of two wrist straps, ground cord assembly, alligator clip, and static dissipating work surface) when working with the modules. The kit is designed to connect the technician and the static dissipating work surface to the same ground point to prevent damage to the modules by electrostatic discharge. 1. Use Static Shielding Bag. Keep the modules in the static shielding bag until you are ready to install them in the system. Save the packaging for future use. 2. Ground Bags before Opening. Before opening a bag containing an assembly with semiconductors, touch it to the equipment housing or a ground to equalize charges. 3. Avoid Touching Circuitry. Handle assemblies by the edges; avoid touching the circuitry. 4. Avoid Partial Connection of Semiconductors. Verify that all devices connected to the module are properly grounded before using them. 5. Ground Test Equipment. 6. Use Antistatic Field Service Vacuum. Remove dust from the module if necessary. 7. Use a Grounded Wrist Strap. Connect the wrist strap to the appropriate grounding plug on the power entry panel. The grounding plug on the power entry panel is connected to the cabinet chassis ground. 8. Do Not Use Lead Pencils to Set Dipswitches. To avoid contamination of dipswitch contacts that can result in unnecessary circuit board malfunction, do not use a lead pencil to set a dipswitch.
INTRODUCTION
This section explains what must be done before placing any INFI-NET to computer interface modules into operation. Read, understand, and complete the steps in the order they appear before operating the modules.UNPACKING AND INSPECTION 1. Examine the hardware immediately for shipping damage. 2. Notify the nearest Bailey Controls sales office of any such damage. 3. File a claim for any damage with the transportation company that handled the shipment. 4. Use the original packing material and container to store the hardware. 5. Store the hardware in an environment of good air quality, free from temperature and moisture extremes. INNIS01 NETWORK INTERFACE SLAVE MODULE CONFIGURATION Both INFI-NET to computer interfaces require an INNIS01 Network Interface Slave Module (NIS). Configure the NIS module as follows.There are four dipswitches on the NIS module. The dipswitches and their functions are described below. See Figure 3-1 for dipswitch locations.This dipswitch sets the node address. Valid node addresses are one through 250. Refer to Table 3-1. Pole one is the MSB bit with a binary weight of 128. Pole eight is the LSB bit with a binary weight of one. Record the dipswitch SW1 settings in the space provided.This dipswitch sets the loop number of the loop off of the main INFI-NET loop. Valid loop numbers are one through 250. Refer to Table 3-2. Record the dipswitch SW2 setting in the space provided.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
