產品詳情介紹
DIAGRAPH 5760019ACM-BS輸出驅動器
除非另有說明以下規格適用于+18之間的3300 XL 8 mm前置器傳感器、延長電纜和8 mm探針?C和+27?C（+64?F至+80?F） ，使用-24 Vdc電源，10 kΩ負載，AISI 4140鋼靶，探針間隙為1.27 mm（50 mils）。性能特征適用于僅由3300 XL 8 mm組件組成的系統。系統精度和互換性規范不適用于校準至AISI 4140鋼靶以外的任何目標的傳感器系統?？山邮芤桓墙佑|式3300系列5 mm、3300 8 mm或3300 XL 8 mm接近探頭和延長電纜。需要-17.5 Vdc至-26 Vdc（無隔離柵），12 mA最大功耗，-23 Vdc到-26 V直流（帶隔離柵）。在高于-23.5 Vdc的正電壓下運行會導致線性范圍減小。當在線性范圍的中心有間隙時，兩個獨立傳感器系統之間的相互作用（串?dāng)_）在軸直徑至少為50 mm（2 in）或更大的軸上將小于50 mV。您應注意保持傳感器尖端的最小間距，通常軸向位置測量至少為40 mm（1.6 in），徑向振動測量至少為38 mm（1.5 in），以將串?dāng)_限制在50 mV或以下。軸直徑小于76.2 mm（3 in）的徑向振動或位置測量通常會改變比例因數。
探頭壓力
3300 XL 8 mm探頭設計用于密封探頭尖端和外殼之間的壓差。探頭密封材料由Viton?O型環組成。探頭在裝運前未進行壓力測試。如果您需要對應用的壓力密封進行測試，請聯系我們的定制設計部門。注：客戶或用戶有責任確保包含所有液體和氣體，并在近貼探頭發生泄漏時進行安全控制。此外，pH值高或低的溶液可能腐蝕探針的尖端組件，導致介質泄漏到周圍區域。Bently Nevada，股份有限公司對3300 XL 8 mm接近型探頭泄漏造成的任何損壞概不負責。此外，由于探針泄漏，3300 XL 8 mm接近型探針不會根據服務計劃更換。鋁夾支架是一種無螺紋安裝支架，設計用于光滑外殼探針（330140、330141、330197和330198）。在為探針設置間隙后，通過擰緊螺釘擰緊夾緊支架。安裝螺釘有預先鉆好的安全線孔。鋁探頭螺紋安裝支架是大多數3300和3300 XL探頭安裝的標準安裝支架。-01選項包括兩個10-24 UNC-2A安裝螺釘。-04選項包括兩個M5 x 0.8-6g安裝螺釘。安裝螺釘有預先鉆好的安全線孔。
Unless otherwise noted
the following specifications are for a 3300 XL 8 mm Proximitor Sensor, extension cable and 8 mm probe between +18 ?C and +27 ?C (+64 ?F to +80 ?F), with a -24 Vdc power supply, a 10 kΩ load, an AISI 4140 steel target, and a probe gapped at 1.27 mm (50 mils). Performance characteristics apply to systems that consist solely of 3300 XL 8 mm components. The system accuracy and interchangeability specifications do not apply to transducer systems that are calibrated to any target other than our AISI 4140 steel target.Accepts one non-contacting 3300-series 5 mm, 3300 8 mm or 3300 XL 8 mm Proximity Probe and Extension Cable.Requires -17.5 Vdc to -26 Vdc without barriers at 12 mA maximum consumption, -23 Vdc to -26 Vdc with barriers. Operation at a more positive voltage than -23.5 Vdc can result in reduced linear range.When gapped at the center of the linear range, the interaction between two separate transducer systems (cross-talk) will be less than 50 mV on shaft diameters of at least 50 mm (2 in) or greater. You should take care to maintain minimum separation of transducer tips, generally at least 40 mm (1.6 in) for axial position measurements or 38 mm (1.5 in) for radial vibration measurements to limit cross-talk to 50 mV or less. Radial vibration or position measurements on shaft diameters smaller than 76.2 mm (3 in) will generally change the scale factor.
Probe Pressure
3300 XL 8 mm probes are designed to seal differential pressure between the probe tip and case. The probe sealing material consists of a Viton? O-ring. Probes are not pressure tested prior to shipment. Contact our custom design department if you require a test of the pressure seal for your application. Note: It is the responsibility of the customer or user to ensure that all liquids and gases are contained and safely controlled should leakage occur from a proximity probe. In addition, solutions with high or low pH values may erode the tip assembly of the probe causing media leakage into surrounding areas. Bently Nevada, Inc. will not be held responsible for any damages resulting from leaking 3300 XL 8 mm proximity probes. In addition, 3300 XL 8 mm proximity probes will not be replaced under the service plan due to probe leakage.The aluminum clamp bracket is an unthreaded mounting bracket designed for use with the smooth case probes (330140, 330141, 330197 and 330198). After gapping the probe, tighten the clamp bracket by tightening the screws. The mounting screws have pre-drilled holes for safety wire.The aluminum probe threaded mounting bracket is the standard mounting bracket for most 3300 and 3300 XL probe installations. The -01 option includes two 10-24 UNC-2A mounting screws. The -04 option includes two M5 x 0.8-6g mounting screws. The mounting screws have pre-drilled holes for safety wire.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
