產品詳情介紹
Honeywell 51305896-100輸出控制卡
安裝連接器板工具和實用工具螺絲刀，開槽0.8 x 4.0 mm匹配連接器板安裝連接器板1。將連接器板插入導軌，凹槽朝上（參見下圖）。將槽安裝到導軌銷中。2.將連接器板放在電纜屏蔽軌道上。3.將兩個外加螺釘固定到底板上。首先擰入下部螺釘，然后擰入上部螺釘。要卸下連接器板1，請從基板上松開固定螺釘。2.從電纜屏蔽軌道上提起連接器板的下部。3.從導軌上拆下連接器板。安裝和拆卸模塊本章介紹如何安裝和拆卸HIMax模塊?？梢栽贖IMax系統運行時安裝和卸下模塊。注意：模塊卡住會損壞總線和電源插座！不遵守這一點可能會損壞控制器。將模塊插入底板時務必小心。工具和工具螺絲刀，開槽0.8 x 4.0 mm螺絲刀，開槽1.2 x 8.0 mm
默認網關的IP地址。ARP老化時間[s]處理器或COM模塊將通信伙伴的MAC地址存儲在MAC/IP地址分配表（ARP緩存）中。如果在1x….2x ARP老化時間……的時間段內收到通信的消息，MAC地址仍存儲在ARP緩存中?！瓫]有收到通信伙伴的消息，MAC地址從ARP緩存中刪除。本地網絡中ARP老化時間的典型值范圍為5…300秒。用戶無法讀取ARP緩存的內容。值范圍：1…3600 s默認值：60 s
在SILVorX中配置模塊
處理器模塊在SILworX硬件編輯器中配置。必須配置處理器模塊的以太網接口。以下各章介紹了詳細視圖選項卡。請確保正確設置IP地址！如果使用路由器或網關，由于雙向傳輸需要額外的時間，用戶必須調整（增加）ARP老化時間。如果ARP老化時間過低，通信伙伴的MAC地址將從ARP緩存中刪除，通信將延遲或中斷。為了獲得高效的性能，ARP老化時間值必須小于為所用協議設置的接收超時。
MAC學習和ARP老化時間用于設置以太網交換機學習MAC地址的速度?？梢赃M(jìn)行以下設置：保守（建議）：如果ARP緩存已經包含通信伙伴的MAC地址，則這些地址將被鎖定，并且在至少一個ARP老化時間和最多兩個ARP衰老時間段內，不能被其他MAC地址替換。這確保了數據包不會被有意或無意地轉發給外部網絡參與者（ARP欺騙）。容差：當接收到消息時，消息中包含的IP地址與ARP緩存中的數據進行比較，存儲在ARP緩存的MAC地址立即被消息中的MAC地址覆蓋。如果通信的可用性比控制器的授權訪問更重要，則必須使用容差設置。默認設置：保守
Mounting a Connector Board
Tools and utilities ? Screwdriver, slotted 0.8 x 4.0 mm ? Matching connector board To install the connector board 1. Insert the connector board into the guiding rail with the groove facing upwards (see following figure). Fit the groove into the guiding rail pin. 2. Place the connector board on the cable shield rail. 3. Secure the two captive screws to the base plate. First screw in the lower than the upper screw. To remove the connector board 1. Release the captive screws from the base plate. 2. Lift the lower section of the connector board from the cable shield rail. 3. Remove the connector board from the guiding rail.Mounting and Removing the Module This chapter describes how to mount and remove the HIMax module. A module can be mounted and removed while the HIMax system is operating. NOTICE Damage to bus and power sockets due to module jamming! Failure to observe this can damage the controller. Always take care when inserting the module in the base plate.Tools and utilities ? Screwdriver, slotted 0.8 x 4.0 mm ? Screwdriver, slotted 1.2 x 8.0 mm
IP address of the default gateway. ARP Aging Time [s] A processor or COM module stores the MAC addresses of the communication partners in a MAC/IP address assignment table (ARP cache). If in a period of 1x....2x ARP Aging Time ... ? ... messages of the communication are received, the MAC address remains stored in the ARP cache. ? ... no messages of the communication partner are received, the MAC address is erased from the ARP cache. The typical value for the ARP Aging Time in a local network ranges from 5...300 s. The user cannot read the contents of the ARP cache. Range of values: 1...3600 s Default value: 60 s
Configuring the Module in SILWorX
The processor module is configured in the SILworX Hardware Editor. The Ethernet interface of the processor module must be configured. Each of the following chapters describes a detail view tab. Ensure proper setting ot the IP address!If routers or gateways are used, the user must adjust (increase) the ARP Aging Time due to the additional time required for twoway transmission. If the ARP Aging Time is too low, the MAC address of the communication partner is erased from the ARP cache, the communication is delayed or interrupted. For an efficient performance, the ARP aging time value must be less than the receive timeout set for the protocols in use.
MAC Learning and ARP Aging Time are used to set how quick the Ethernet switch should learn the MAC address. The following settings are possible: ? Conservative (recommended): If the ARP cache already contains MAC addresses of communication partners, these are locked and cannot be replaced by other MAC addresses for at least one ARP Aging Time and a maximum of two ARP Aging Time periods. This ensures that data packets cannot be intentionally or unintentionally forwarded to external network participants (ARP spoofing). ? Tolerant: When a message is received, the IP address contained in the message is compared to the data in the ARP cache and the MAC address stored in the ARP cache is immediately overwritten with the MAC address from the message. The Tolerant setting must be used if the availability of communication is more important than the authorized access to the controller. Default setting: Conservative
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
