3BSE001440R1通道觸點配套卡件
電源部分的散熱器溫度一些DCS轉換器通過PTC元件進行監控。其他DCS轉換器檢查冷卻空氣
溫度和氣流。第三種選擇是：一個，用于測量風扇電流限制。如果風扇電流過低或根本沒有風扇電流或風扇電流過高，驅動器需要關閉。風扇電流可能過低
-風扇可能未打開，或數據
交流輸入/輸出電壓：單相；230伏
交流輸入/輸出電流：5A
交流峰值電流：根據風機啟動電流；需要外部開關設備
交流隔離電壓：690 V（通過自耦變壓器供電）
負載：帶啟動電容器的單相交流電機
頻率：50 Hz/60 Hz
輸出數據：無源器件；僅與DCS電子設備一起使用
端子截面積：X92：電源；最大2.5 mm2
X11：至X31：電機連接；6.3毫米faston
電流縮放：負載電阻R100/R101；R100/R101=120
互連：參見部分電源部分DCP變流器的冷卻
5.9.1 PW 1002
本設備的設計和使用專用于
默認情況下，直接高于800 A的DCP轉換器條件它由230 V單相供電電源和將監控兩個單相并聯安裝在轉換器頂部的風扇配置傳輸特性是相同的與PW 1003中描述的相同
本手冊中的電源部分冷卻顯示電源和風扇和接口板PG 7xx3。
-風機電源內的任何保護裝置具有：行動或電線斷了
-螺旋槳松動或類似的東西
風扇電流可能過高，因為：-風扇可能被機械堵塞，或-風扇繞組短路或類似故障
加速期間的過電流可通過軟件抑制。本裝置設計用于：任何類型重建應用程序的DCR套件。它可以
監控單相或三相風機的電流
它可以級聯，這意味著多個設備可以連接到一個PTC輸入，以監控多個風扇電流。傳遞特性如圖5.9/3所示，需要適應通過改變負載電阻，風扇電流或通過軟件參數，取決于類型已用于現有電源部件的風扇。
The heatsink temperature of the power part of
some DCS converters is monitored via a PTC element. Other DCS converters check the cooling air
temperature and the airflow. The third option is this
one, which measures the fan current being within
limits. In case the fan current is too low or there is
no fan current at all or it is too high, the drive needs
to be switched off. The fan current may be too low
because
- the fan may not be switched on or
Data
AC input / output voltage: single phase; 230 V
AC input / output current: 5 A
AC peak current: according to fan starting current; external switching device needed
AC isolation voltage: 690 V (supply via autotransformer)
Load: single phase AC motors with starting capacitor
Frequency: 50 Hz / 60 Hz
Output data: passive device; to be used together with DCS electronics only
Terminal cross sectional area: X92: power supply; max. 2.5 mm2
X11: to X31: motor connection; 6.3 mm faston
Current scaling: burden resistor R100 / R101; R100/R101 = 120 each
Interconnection: See part power section cooling of DCP converters
5.9.1 PW 1002
This device is designed and used exclusively at
DCP converters above 800 A directly in default
condition. It is supplied by a 230 V single phase
power supply and will monitor the two single phase
fans mounted on top of the converter in parallel
configuration. The transfer characteristic is identical
to the one described at the PW 1003. The part
power section cooling within this manual shows the
interconnections between the power supply, the
fans and the interface board PG 7xx3.
- any protection device within the fan supply has
acted or
- a wire is broken or
- the propeller became loose or something similar
The fan current may be too high because
- the fan may be blocked mechanically or
- there is a short circuit in the fan winding or something similar
The overcurrent during acceleration can be suppressed by the software.This device is designed to be used together with
the DCR kit at any type of rebuild application. It can
monitor the current of single or three phase fans
and it can be cascaded, which means multiple devices can be connected to one PTC input to monitor several fan current. The transfer characteristic
shown at figure 5.9/3 needs to be adapted to the
fan current either by changing the burden resistors
or by a software parameter, depending on the type
of fan already used for the existing power part.
