3BSE008358R1控制處理卡件
標準電壓調整：KCR 760電壓調節器配備
內部電壓范圍調整電位計和自動電壓調整
用于遠程安裝的變阻器。自動電壓調節變阻器允許：
將發電機電壓調整到標稱值的±10%左右感測電壓。
寬范圍電壓調整：適用于電壓必須調整超過標稱值±10%，寬范圍電壓調整
可為發電機組提供電路。這個附件是設計用于遠程安裝，并在發電機感應線和調節器感應端子。
并聯運行部件：KCR 760電壓調節器包括并聯運行無功電壓降變壓器（T2）和并聯電壓降電位計（R4）。對于并聯運行，每臺發電機必須配備用于感應無功電流的電流互感器。
變壓器可以具有1A或5A次級。當a 1 a使用電流互感器，二次引線連接至調節器端子CT和CT1。當使用5A電流互感器時二次連接至調節器端子CT和CT5。
電磁干擾? 過濾器：當規格? 購買中的ed訂購：KCR 760調節器可提供EMI? 作為一個外部附件。
輸入功率負載隔離或電壓匹配變壓器：負載
隔離變壓器和電壓匹配變壓器是以下附件
安裝在電壓調節器外部。負載隔離變壓器為：
可提供120 V一次/120 V二次（用于標準120 Vac輸入電源電壓調節器），或240 Vac主電源/240 Vac
次級（用于240 Vac輸入功率調節器）。負載隔離
對于頻率為調節器的輸入功率不同于感應頻率，例如400 Hz電動發電機應用，其中調節器輸入功率
取自50/60 Hz電動發電機組輸入電源線。電壓匹配變壓器適用于可用的應用
電壓不同于電壓調節器額定輸入電壓?，F(xiàn)場斷路器：規格時? 在采購訂單中
發電系統可配備：? eld斷路器
發電機? eld保護。
電壓關斷開關：規格時? 在采購訂單中
發電系統可配備一個開關，該開關電連接：在向調節器提供輸入功率的線路中。這種保護
該設備建議用于發動機驅動的發電機應用，而不是：配備? eld斷路器或低頻保護。
Standard voltage adjust: KCR 760 voltage regulators are provided with
an internal voltage range adjust potentiometer and an auto voltage adjust
rheostat for remote mounting. The auto voltage adjust rheostat permits
adjustment of generator voltage approximately ±10% from the nominal
sensing voltage.
Wide-range voltage adjust: For applications where voltage must be
adjusted more than ± 10% from nominal, wide range voltage adjust
circuitry can be provided with the generator set. This accessory is
designed for remote mounting and is electrically connected between the
generator sensing lines and the regulator sensing terminals.
Parallel operation components: KCR 760 voltage regulators include a
parallel operation reactive voltage droop transformer (T2) and a parallel
voltage droop potentiometer (R4). For parallel operation each generator
must be equipped with a current transformer for sensing reactive current.
The transformer may have either a 1 A or 5 A secondary. When a 1 A
current transformer is used, the secondary leads connect to regulator
terminals CT? and CT1. When a 5 A current transformer is used, the
secondary connects to regulator terminals CT? and CT5.
Electromagnetic interference ? lters: When speci? ed in the purchase
order the KCR 760 regulator can be supplied with EMI ? lters as an
external accessory.
Input power load isolation or voltage matching transformers: Load
isolation and voltage matching transformers are accessory items that
mount external to the voltage regulator. Load isolation transformers are
available with 120 V primary/120 V secondary (for use with standard
120 Vac input power voltage regulators), or 240 Vac primary/240 Vac
secondary (for use with 240 Vac input power regulators). Load isolation
transformers are recommended for any application where frequency of
the input power to the regulator is different from the sensing frequency, such as 400 Hz motor-generator applications where regulator input power
is taken from 50/60 Hz motor-generator set input power lines. Voltage
matching transformers are available for applications where available
voltage is different from the voltage regulator rated input voltage.
Field circuit breaker: When speci? ed in the purchase order, the
generating system can be provided with a ? eld circuit breaker for
generator ? eld protection.
Voltage shutdown switch: When speci? ed in the purchase order, the
generating system can be supplied with a switch that electrically connects
in the line that supplies input power to the regulator. This protective
device is recommended for engine driven generator applications not
provided with ? eld circuit breaker or underfrequency protection.
