PM510V16控制處理器
標準功能和選項
標準KCR 760電壓調節器提供的功能，選件
本系列可供選擇，可提供各種附件
發電機組的電壓調節系統在以下段落。哪些選項是特定的? 在采購訂單中，在工廠調節器內進行所需的電路更改而附件是安裝在調節器外部的部件。
標準傳感：基本KCR 760調節器使用單相50/60Hz感測。傳感變壓器具有多抽頭一次允許
在100至600 Vac的感測電壓下操作。標準調節器包括降低中電壓的欠頻限制電路
當速度下降到UFL以下時，頻率下降的比例操作閾值。標準50/60 Hz傳感調節器中的UFL
對于50 Hz的應用，使用48 Hz的操作閾值進行調整對于60Hz的應用為58Hz。
可選傳感：當規格? ed：在采購訂單中，監管機構可以在感測電路中提供以下變化：-三相50/60 Hz，100至600 Vac感應。
-UFL設置為49.5/59.5 Hz，用于渦輪增壓發動機。
-每赫茲電壓電路代替UFL，用于以下應用：
在以下速度范圍內，電壓必須與頻率成比例：
額定轉速降至約1/2額定轉速。
-400 Hz，單相或三相，100至600 Vac，帶385 Hz UFL操作閾值。
-具有高于或低于385Hz的UFL閾值的400Hz。
-50/60 Hz或400 Hz，單相或三相100至600 Vac，帶? 在電動發電機組或變頻/恒頻調節
電壓應用。監管機構? at法規將不包括：UFL或V/Hz電路。
標準輸入功率和直流輸出
標準KCR 760穩壓器
使用單相120 Vac±10%輸入功率，具有額定最大值
連續輸出65VDC，10A；90 Vdc，15 A一分鐘? 埃爾德強迫。
可選輸入功率和直流輸出：當規格? 購買中的ed訂購時，KCR 760調節器可為modi? 教育署將從單一相，240 Vac±10%輸入功率，因此具有額定最大值連續輸出125 Vdc，10 A；180 Vdc，15 A一分鐘? 埃爾德強迫。領域? 灰化：KCR 760電壓調節器包括固態? 埃爾德? 灰化電路。
標準保險絲：標準KCR 760穩壓器配有15 a
穩壓器內輸入電源電路中的正常熔斷保險絲。這保險絲提供電壓調節器過載保護。
可選保險絲：在系統不包括? 埃爾德
斷路器和發電機? 需要eld保護，較小的保險絲可以使用。發電機? eld保護，保險絲電流強度應為1
是勵磁機的一半到兩倍? 連接額定負載時的eld電流
至發電機。保險絲電流強度不得超過15 A或三分之二開路電路強制。
Standard features and options Features provided in standard KCR 760 voltage regulators, options available in this series, and various accessories that can be supplied with the generator set voltage regulating system are described in the paragraphs that follow. Where options are speci? ed in the purchase order, the required circuitry changes are made within the regulator at the factory while accessories are parts that mount external to the regulator. Standard sensing: The basic KCR 760 regulator uses single phase 50/60 Hz sensing. The sensing transformer has a multi-tap primary permitting operation at sensing voltages of 100 to 600 Vac. The standard regulator includes an underfrequency limit circuit that decreases voltage in proportion to the decrease in frequency when speed drops below the UFL operational threshold. The UFL in standard 50/60 Hz sensing regulators is adjusted with an operational threshold of 48 Hz for a 50 Hz application and 58 Hz for a 60 Hz application. Optional sensing: When speci? ed in the purchase order the regulator can be supplied with the following variations in sensing circuitry: - Three phase 50/60 Hz, 100 to 600 Vac sensing. - UFL set 49.5/59.5 Hz for use with turbocharged engines. - Volts-per-hertz circuitry in place of UFL for applications where voltage must be proportional to frequency over a speed range from rated rpm down to approximately 1/2 rated speed. - 400 Hz, single or three-phase, 100 to 600 Vac with 385 Hz UFL operational threshold. - 400 Hz with UFL threshold higher or lower than 385 Hz. - 50/60 Hz or 400 Hz, single or three-phase 100 to 600 Vac with ? at regulation for a motor-generator set or variable frequency/constant voltage applications. Regulators with ? at regulation will not include UFL or V/Hz circuitry. Standard input power and dc output: Standard KCR 760 regulator uses single-phase, 120 Vac ±10% input power and has rated maximum continuous output of 65 Vdc, 10 A; 90 Vdc, 15 A one-minute ? eld forcing. Optional input power and dc output: When speci? ed in the purchase order, the KCR 760 regulator may be modi? ed to operate from single phase, 240 Vac ±10% input power and thereby have rated maximum continuous output of 125 Vdc, 10 A; 180 Vdc, 15 A one-minute ? eld forcing.
