3BSE019216R1數字信號卡件
90-70系列總線控制器和網絡的硬件配置
從Control 90機架顯示器中選擇總線控制器以編輯硬件
總線控制器和網絡的配置。選擇工具后，進行編輯硬件配置，以下選項卡可用：
設置I/O機架驅動器
可編程邏輯控制器
站（控制站）通用設備掃描通訊員
協議文件功耗
選擇后，這些選項卡顯示從FIP配置的參數網絡配置工具。已使用網絡配置的參數配置工具僅在更新后顯示。
設置
選擇設置選項卡以配置總線控制器?？偩€的不可編輯項控制器包括是否是主用戶、是否是總線仲裁器、時鐘
同步等。狀態數據長度（80位或5字）不可編輯，但是您可以更改當前分配給總線的參考地址
控制器的狀態數據。IP地址、子網掩碼和網關IP地址應分配給您的網絡管理員。如果地址
設置不正確，您的設備可能無法通過網絡和CAN進行通信
中斷通信。對于沒有網關的簡單隔離網絡，分配格式為3.0.0.x（x）的唯一地址
范圍從1到255）。協議文件
最多可在此處輸入8個用戶協議文件的目錄路徑規范。通訊員
顯示與此FIP總線控制器交換I/O數據的所有設備的列表。
所有字段都不可編輯
–如果“受控設備”為否，則該設備僅由FIP總線控制器監控。
FIP總線控制器不能配置或影響I/O的操作模式支架
–如果“受控設備”為是，則該設備由FIP總線控制器控制。這個FIP總線控制器可以配置設備并控制其工作模式。I/O機架、驅動器、PLC、工作站和通用設備根據需要選擇I/O機架、驅動器、PLC、工作站和通用設備選項卡，以：配置網絡上的設備。這些選項卡上的不可編輯項包括設備名稱、機架、插槽、TVA類型以及所列設備是否生產或消費數據為各個設備配置以下參數。
Hardware Configuration for the Series 90-70 Bus Controller and the Network
Select the Bus Controller from the Control 90 rack display to edit the Hardware
Configuration for the Bus Controller and the network. When you select Tools then Edit
Hardware Configuration, the following tabs are available:
Settings
I/O Racks
Drives
PLCs
Stations (control stations)
Generic Devices
Scanning
Correspondents
Protocol Files
Power Consumption
When selected, these tabs display parameters that have been configured from the FIP
Network Configuration tool. Parameters that have been configured with the Network
Configuration Tool appear only after an update.
Settings
Select the Settings tab to configure the Bus Controller. Non-editable items for the Bus
Controller include whether it is the master subscriber, whether it is the bus arbiter, clock
synchronization, and others. The status data length (80 bits or 5 words) is not editable,
but you can change the reference address that is presently assigned for the Bus
Controller’s status data.The IP Address, Subnet Mask, and Gateway IP Address should be assigned by
your network administrator. If addresses
are improperly set, your device may not
communicate on the network and could
disrupt communications. For a simple, isolated network with no gateways, assign a
Unique address in the format 3.0.0.x (x
ranges from 1 to 255).Protocol Files
Directory path specifications for up to 8 User Protocol Files may be entered here.
Correspondents
A list of all the devices that exchange I/O data with this FIP Bus Controller is displayed.
All the fields are non-editable.
– If “Controlled Device” is NO, this device is only monitored by the FIP Bus Controller.
The FIP Bus Controller cannot configure or affect the operating mode of the I/O
rack.
– If “Controlled Device” is YES, this device is controlled by the FIP Bus Controller. The
FIP Bus Controller can configure the device and control its operating mode.
I/O Racks, Drives, PLCs, Stations , and Generic Devices
Select the I/O Racks, Drives, PLCs, Stations, and Generic Devices tabs as necessary to
configure the devices on the network. Non-editable items on these tabs include the
device name, rack, slot, TVA type, and whether the listed devices produce or consume
data. Configure the following parameters for individual devices.
