3BSC980006R152工控卡件
該模塊使用操作員面板操作，該面板包括使用輸入MD打開的綠色和紅色LED。
HI（1）輸入將點亮綠色LED，LO將點亮紅色LED。默認連接將是的PS輸出
但應根據需要進行更改，以顯示正確的狀態。消息參數不適用于當前產品。
通電-當交換機配置為：瞬時動作，它將始終在NC位置。對于持續行動，與通電參數設置為“是”，開關將在炎熱或溫暖天氣下，在最后一個位置通電啟動，在冷啟動期間，將在NC位置。當加電參數為設置為“否”，開關將在最后一次通電熱啟動期間的位置。在溫暖或寒冷期間啟動時，它將在NC位置通電。PB3SW是三種通用開關之一，在每個循環中可用。它可以用于切換布爾信號在以下應用中：?jiǎn)?dòng)/停止，控制TSW（轉換開關）的位置用于切換模擬信號的功能塊，或其他操作員啟動操作。PB3SW只能運行當A/M功能塊具有未配置。PB3SW可配置為瞬時或持續活動作為瞬時，開關將切換到按下按鈕時無位置，按鈕將返回
當釋放時。在持續模式下，開關將每次按下按鈕時的交替位置。一未配置的NC輸入默認為0，并且未配置無輸入1。固件為1.30和更高，按鈕可以通過通過Modbus或LIL的命令。
該模塊使用操作員面板操作，該面板包括使用輸入MD打開的綠色和紅色LED。
HI（1）輸入將點亮綠色LED，LO將點亮紅色LED。默認連接將是的PS輸出
但應根據需要進行更改，以顯示正確的狀態。消息參數不適用于
當前產品。通電-當交換機配置為：瞬時動作，它將始終在NC位置。對于持續行動，與通電參數設置為“是”，開關將在炎熱或溫暖天氣下，在最后一個位置通電啟動，在冷啟動期間，它將在NC位置。當加電參數為設置為“否”，開關將在最后一次通電熱啟動期間的位置。在溫暖或寒冷期間start將在NC位置通電。
This block operates with an operator faceplate that includes green and red LEDs that are turned on using input MD.
A HI (1) input will turn on the Green LED and a LO the Red LED. The default connection will be the PS output of
the block but should be changed as required to display the correct status. The message parameters do not apply to
the current product.
POWER UP - When the switch is configured for
momentary action, it will always power up in the
NC position. For sustained action, with the
POWER UP parameter set to YES, the switch will
power up in the last position during a hot or warm
start, and during a cold start will power up in the
NC position. When the POWER UP parameter is
set to NO, the switch will power up in the last
position during a hot start. During a warm or cold
start, it will power up in the NC position.PB3SW is one of three general purpose switches,
available in each loop. It can be utilized for switching
Boolean signals in such applications as: Start/Stop,
controlling the position of a TSW (Transfer Switch)
function block for switching analog signals, or other
operator initiated actions. PB3SW can only be operated
from the front panel when the A/M function block has
not be configured.
PB3SW can be configured for momentary or sustained
operation. As momentary, the switch will transfer to the
NO position when the button is pressed and it will return
when released. In the sustained mode, the switch will
alternate positions each time the button is pressed. An
unconfigured NC input defaults to 0 and an
unconfigured NO input to 1. With firmware 1.30 and
higher, the button can be remotely activated through a
command over Modbus or LIL.
This block operates with an operator faceplate that includes green and red LEDs that are turned on using input MD.
A HI (1) input will turn on the Green LED and a LO the Red LED. The default connection will be the PS output of
the block but should be changed as required to display the correct status. The message parameters do not apply to
the current product. POWER UP - When the switch is configured for
momentary action, it will always power up in the
NC position. For sustained action, with the
POWER UP parameter set to YES, the switch will
power up in the last position during a hot or warm
start, and during a cold start it will power up in the
NC position. When the POWER UP parameter is
set to NO, the switch will power up in the last
position during a hot start. During a warm or cold
start will power up in the NC position.
