3EGM030300R0002脈沖輸入卡件
ODC塊是上使用的五個操作員顯示器之一每個循環一個，用于配置本地操作員顯示來自遠程操作員的功能和網絡參數與回路相關的工作站。查看i|ware PC下一頁的面板。
固件1.30及更高版本中包含以下功能。1.一個新參數，視圖OD，當設置為是時默認設置，允許查看操作員顯示并使用循環按鈕本地訪問。在某些情況下在這種情況下，可能需要僅查看顯示或操作網絡工作站的參數，不允許從本地操作或查看控制回路陳列此處，參數應設置為“否”。
2.當循環事件激活時，輸出LE為高（1）。輸出當站錯誤激活時，SE為高。
3.循環#（此參數為版本中的MB索引1.21）用于索引對Modbus的讀取和寫入?yún)?shù)。LIL具有25個參數：C1S、C2S、C3S，..C25S。選擇ODC塊后，以及循環#已配置，相應的C#LIL參數將包含LIL起始通道（n）地方必須輸入循環#才能啟用LIL或Modbus通信。
過程/設定點和閥門的范圍指針必須配置條形圖以定義P、S和V的變量輸入。如果這些參數不是配置后，將使用工程圖縮放條形圖范圍為0.00到100.00。X和Y的范圍指針定義顯示的小數點位置和單位代碼。
該信息還定義了循環的縮放通過提供給遠程工作站的信息網絡（即Modbus或LIL）。
輸入變量P、S、V、X和Y顯示在數字顯示中，使用工程單位和首選范圍指針的DPP。在BATOT內配置時，也將顯示BATOT的總計塊如果值大于DPP參數允許的值，小數點將移動以允許顯示
顯示完整數字，直到超過最大可用數字，此時將指示超出范圍。
當輸入U(xiǎn)1或U2變?yōu)楦撸?）時，8字符的用戶狀態（U_status）將顯示為狀態優先級（U_優先）。優先級為0將禁用該狀態功能，將狀態字中的位設置為0。
有關使用優先級1至5的顯示動作的說明，請參見第9節“操作”。
水平條形圖可以選擇為直接作用或反向作用。此功能允許它始終指示完全點亮?xí)r打開閥門。基本面板上的標簽是固定的，但粘貼標簽可用于更改適應癥。V NET AC參數允許為直接或反向動作設置LxVI網絡參數。
這使得HMI上的閥桿能夠與面板上的閥條類似地操作。左欄和右欄應相應設置標簽（例如，左=打開，右=關閉）。操作員顯示器必須配置為將控制器回路數據映射到網絡數據。環路網絡數據已映射
當使用標準Modbus接口時，進入寄存器或線圈，當可選LIL時，進入通道/參數已添加接口。Modbus和LIL的映射列于“網絡”中的表格中
ODC blocks are one of five operator displays that are used on a one per loop basis to configure the local operator display functions and network parameters from a remote operator workstation associated with the loop. See the i|ware PC faceplate on the next page. The following features are in firmware 1.30 and higher. 1. A new parameter, VIEW OD, when set to YES, the default setting, enables the operator display to be viewed and accessed locally using the LOOP button. In some cases, it may be desired to view only display or operation parameters with a network workstation and not allow operation or viewing of the control loop from the local display. Here the parameter should be set to NO. 2. Output LE is high (1) when a loop event is active. Output SE is high when a station error is active. 3. The LOOP # (this parameter was MB INDEX in version 1.21) is used to index reads and writes to Modbus parameters. The LIL has 25 parameters: C1S, C2S, C3S, ..... C25S. When an ODC block has been selected and the LOOP # has been configured, the corresponding C#S LIL parameter will contain the LIL starting Chan (n) location. The LOOP# must be entered to enable either LIL or Modbus communications. Range pointers for both the process/setpoint and valve bargraphs must be configured to define the range of the variable inputs to P, S, and V. If these parameters are not configured, the bargraphs will be scaled using the engineering range of 0.00 to 100.00. The range pointer for X and Y define the displayed decimal point position and the units code. This information also defines the scaling of the loop information provided to a remote workstation over the network (i.e. Modbus or LIL). Input variables P, S, V, X, and Y are shown in the numeric display, using the engineering UNITS and the preferred DPP of the range pointer. The Total from the BATOT will also be displayed when configured within the BATOT block. If a value is greater than allowed by the DPP parameter, the decimal point will be shifted to allow the display to show the full number, until it exceeds the maximum available digits, at which time it will indicate over range. When input U1 or U2 goes high (1), the 8-character user status (U_STATUS) will be displayed as configured by the status priority (U_ PRIOR). A priority of 0 will disable that status function setting the bits in the status word to 0. See Section 9 Operation for a description of display actions using priorities 1 to 5. The horizontal bargraph can be selected as direct or reverse acting. This feature allows it to always indicate an OPEN valve when fully lit. The labels on the basic faceplate are fixed, but paste on labels can be used to change the indications. The V NET AC parameter allows the LxVI network parameter to be set for direct or reverse action. This enables the valve bar on the HMI to operate similar to the valve bar on the faceplate. The left and right bar labels should be set accordingly (e.g. Left = “OPEN & Right = CLOSE). An operator display must be configured to map controller loop data to network data. Loop network data is mapped into registers or coils when the standard Modbus interface is used and to channels/parameters when the optional LIL interface has been added. Mappings for both Modbus and LIL are listed in the tables included in the ‘Network
