FBM204電壓輸入模塊
MB REG參數標識數字?jǐn)?shù)據在源設備中的位置。REG TYP參數
啟用保持寄存器（Modbus功能代碼03）或輸入寄存器（Modbus功能代碼04）的讀取。
在大多數Modbus設備中，兩者都被視為相同的，但輸入類型是最常見的用法。能源部的使用
其他西門子摩爾控制器中的塊作為輸入源，通過使用來自下表。UD速率參數配置塊請求數據的速率。P2P設置
將以以太網塊中的P2P速率參數設置的速率更新數據。Ct設置將更新
控制器循環時間的數據。
輸出QS指示接收數據的質量，當數據不好時，輸出QS將變高（1）。這通常是
與由于通信故障或源的錯誤配置而無法接收數據相關。DIL_當可選的LIL
已安裝通信板。DIL區塊編號為：
在全站范圍內，按照每次使用的順序分配。街區
允許站點從另一個站點獲取全局字（GW）LIL上的車站。
功能塊有16個輸出，D0到DF，其中表示全局字中位0-F的值。輸出QS
指示接收數據的質量，并將變高（1）
當數據不好時。這通常與以下故障相關：
由于LIL故障或配置錯誤而接收全局?jǐn)?shù)據來源。接收到的全局字也將作為配置信道中的參數1值由該站重新發送n、 DIN_功能塊可用于檢測離散
來自外部源的信號，并提供塊輸出表示該信號的狀態。區塊可用在控制器板和擴展器板上。
功能塊名稱（ID）和端子代號為：在第8.4節中列出。
當輸入為on和low時，塊輸出為high（1）（0）關閉時。
輸出QS表示輸出信號的質量狀態
并且當輸出質量差時將為高（1）。
質量差表示輸入的任何硬件故障
轉換器。DINU_塊具有多功能功能：
?感測離散輸入并提供高（1）或低
（0）表示輸入狀態的輸出
?累計和縮放輸入脈沖的計數
?將輸入脈沖速率轉換為縮放模擬頻率輸出
The MB REG parameter identifies the location of the digital data in the source device. The REG TYP parameter
enables reading of Holding Registers (Modbus Function Code 03) or Input Registers (Modbus Function Code 04).
Both are treated the same in most Modbus devices but the Input type is the most common usage. The use of DOE
blocks in other Siemens MOORE controllers as the input source is defined by using the Modbus Registers from the
table below. The UD RATE parameter configures the rate at which the block will request data. The P2P setting
will update the data at the rate set by the P2P RATE parameter in the ETHERNET block. The Ct setting will update
the data at the cycle time of the controller.
Output QS indicates the quality of the received data and will go high (1) when the data is bad. This is normally
associated with failure to receive data due to a communication failure or a misconfiguration of the source. DIL_ function blocks are available when the optional LIL
communication board is installed. DIL block numbers are
assigned in sequence with each use, station wide. The block
allows the station to obtain a global word (GW) from another
station on the LIL.
The function block has 16 outputs, D0 through DF, which
represent the values of bits 0-F in the global word. Output QS
indicates the quality of the received data and will go high (1)
when the data is bad. This is normally associated with failure to
receive global data due to a LIL failure or a misconfiguration of
the source.
The received global word will also be re-transmitted by this station as a parameter 1 value in the configured channel
n. DIN_ function blocks can be used to sense a discrete
signal from an external source and provide a block output
representing the state of this signal. Blocks are available
on the Controller Board and on the Expander Board.
Function block names (IDs) and terminal designators are
listed in Section 8.4.
The block output is high (1) when the input is on and low
(0) when off.
Output QS indicates the quality status of the output signal
O1 and will be high (1) when the output is of bad quality.
Bad quality indicates any hardware failure of the input
converter.DINU_ blocks have multi-function capability:
? sensing a discrete input and providing a high (1) or low
(0) output representing the state of the input
? totalizing and scaling the count of input pulses
? converting the rate of input pulses to a scaled analog
frequency output
