ADEPT 12000-310工控模塊
機架時鐘位于工程卡中，但由于工程卡沒有顯示，必須選擇控制卡才能
啟用要顯示的時間和日期。哪一個無關緊要選擇控制卡。
如果工程鑰匙安裝在工程卡上，時間和日期可以調整。
3.3.14禁止按鈕
當操作禁止按鈕時，所選控制卡為置于禁止模式。這會阻止任何已配置的繼電器輸出報警功能。
僅當工程鑰匙安裝到工程上時，才能使用Inhibit但是，如果工程鑰匙隨后被移除所選控制卡保持在禁止模式。
3.3.15工程串口
工程串行端口是一個微型DIN插座，提供：
三個功能：a、 解鎖工程師的工程鑰匙連接點功能。
b、 外部工程接口的連接點，允許：每個控制卡由運行配置軟件。
c、 串行打印機的連接點，可用于提供控制卡配置數據和狀態的硬拷貝。
工程串行端口及其工程鍵如下所示：對于歐盟的安裝，請參考EN60079-14:1997“電氣”危險區域內的裝置（地雷除外）。此外，關于選擇、安裝和維護的實踐規范，
檢測和維護設備的使用和維護必須遵守可燃?xì)怏w或氧氣的測量具有參考EN 50073。
上述標準適用于系統57，因?yàn)閭鞲衅鳎嚎赡馨惭b在潛在危險環境中。
此外，適當?shù)牡胤交驀?guó)家法規應：過去?！?/p>
重要通知
1.Zellweger Analytics Limited不承擔以下責任：安裝和/或使用其設備，如果未在根據以下文件的適當發行和/或修訂：手冊。
2.本手冊的用戶應確保其適用于待安裝和/或操作的確切設備的所有細節。
如有疑問，用戶應聯系Zellweger Analytics Limited征求意見。
3.系統57卡不包含用戶可維修部件。參考所有服務均由合格的服務人員提供。
4.插入或移除系統組件時，確保：電源已關閉。否則可能導致系統損壞。
The rack clock is located in the Engineering Card, however since the
Engineering Card has no display, a control card must be selected to
enable the time and date to be displayed. It does not matter which
control card is selected.
If the Engineering Key is fitted to the Engineering Card, the time and date
can be adjusted.
3.3.14 INHIBIT Push-button
When the INHIBIT push-button is operated, the selected control card is
placed in the inhibit mode. This prevents the operation of any configured
relay output alarm functions.
Inhibit can only be used if the Engineering Key is fitted to the Engineering
Card, however, if the Engineering Key is subsequently removed the
selected control card remains in the inhibit mode.
3.3.15 Engineering Serial Port
The Engineering Serial Port is a miniature DIN socket which provides
three functions:
a. Connection point for the Engineering Key to unlock the engineers
functions.
b. Connection point for the External Engineering Interface which allows
each control card to be configured by an external PC running the
configuration software.
c. Connection point for a serial printer which can be used to provide a
hard copy of the control card configuration data and status.
The Engineering Serial Port and its Engineering Key are shown below:For installations in the EU, refer to EN60079-14:1997, ‘Electrical
Installations in Hazardous Areas (other than mines).
Additionally, the code of practice regarding Selection, installation,
use and maintenance of apparatus for the detection and
measurement of combustible gases or oxygen must be complied
with. Refer to EN 50073.
The above standards apply to the System 57 since the SENSORS
may be installed in potentially hazardous atmospheres.
In addition, appropriate local or national regulations shall be
used.”
IMPORTANT NOTICES
1. Zellweger Analytics Limited can take no responsibility for
installation and/or use of its equipment if this is not done in
accordance with the appropriate issue and/or amendment of
the manual.
2. The user of this manual should ensure that it is appropriate in
all details to the exact equipment to be installed and/or operated.
If in doubt, the user should contact Zellweger Analytics Limited
for advice.
3. The System 57 cards contain no user serviceable parts. Refer
all servicing to qualified service personnel.
4. When inserting or removing system components ensure that
the power is switched off. Failure to do this may result in
damage to the system.
