3BHE023681R0102通道卡件
根據配置，主報警或表決報警可能不會給出單獨的報警輸出。
h、 分區報警*分區報警由任何控制通道的輸入引起，從指定區域中的傳感器，超過預先配置的閾值。這個控制裝置上的相關LED（A1、A2、A3、故障、禁止）將點亮帶有報警條件的卡以及指定的控制卡區域主卡（除非安裝了高完整性繼電器卡）。i、 主報警器*任何指定控件的輸入都會導致主報警單個機架內的通道超過預先配置的閾值。這個控制裝置上的相關LED（A1、A2、A3、故障、禁止）將點亮帶有報警條件的卡以及指定的控制卡主卡（除非裝有高完整性中繼卡）。投票警告*
投票報警是由同時存在相同的預配置組內多個控制信道上的報警。相關LED（A1、A2、A3、故障、禁止）將在帶有報警條件的控制卡以及控制卡指定的投票主卡（除非裝有高完整性中繼）。
投票補償（僅限2V6及以上版本軟件）可能為：通過選擇以下選項之一
應用于表決報警輸出操作：
以下配置：
a、 沒有補償。
b、 故障被視為報警。
c、 故障和抑制被視為報警。
d、 故障時的投票數減少。
e、 故障和禁止時的投票數減少。
表決補償有助于確保傳感器發生故障（或禁止）不阻止表決報警輸出。
k、 更新報警（僅限2Vx軟件版本）
更新報警設施提供通用報警指示
無論何時發生新的報警，即使以前的報警條件
存在。更新報警可配置為在單個信道或分組報警。例如主控或分區。
更新警報在僅配置了的系統中特別有用主繼電器或組/區域繼電器，其與以下原因相比，報警不會導致進一步的繼電器輸出：初始警報。
相關LED（A1、A2、A3、故障、禁止）將在具有第2.3節所述報警條件的控制卡。
當繼電器用于信號更新報警時，無其他報警或者消息必須被分配給它們。更新配置應避免出現“禁止”消息。
上升警報
上升報警由以下參數的上升水平引起：
測量值超過預先配置的閾值，也將導致
相關報警LED點亮。
Depending upon the configuration, control cards configured for Zoned,
Master or Voted alarms may not give individual alarm outputs.
h. Zoned Alarm*
A zoned alarm is caused by the input to any control channel, from a
sensor in a designated area, crossing a preconfigured threshold. The
relevant LED (A1, A2, A3, Fault, Inhibit) will illuminate on the control
card with the alarm condition and also on the control card designated
the Zone Master Card (unless it is fitted with a High Integrity Relay
Card).
i. Master Alarm*
A master alarm is caused by the input to any designated control
channel within a single rack crossing a preconfigured threshold. The
relevant LED (A1, A2, A3, Fault, Inhibit) will illuminate on the control
card with the alarm condition and also on the control card designated
the Master Card (unless it is fitted with a High Integrity Relay Card).Voted Alarm*
A voted alarm is caused by the simultaneous presence of an identical
alarm on more than one control channel within a preconfigured group.
The relevant LED (A1, A2, A3, Fault, Inhibit) will illuminate on the
control cards with the alarm condition and also on the control card
designated the Vote Master Card (unless it is fitted with a High
Integrity Relay).
Vote compensation (Version 2V6 and above Software only) may be
applied to the voted alarm output operation by selecting one of the
following configurations:
a. No compensation.
b. Faults counted as alarms.
c. Faults and inhibits counted as alarms.
d. Vote count reduction on faults.
e. Vote count reduction on faults and inhibit.
Vote compensation is useful to ensure that sensors in fault (or
inhibit) do not prevent voted alarm outputs.
k. Update Alarm (Version 2Vx Software only)
The update alarm facility provides a common alarm indication
whenever a new alarm occurs, even if a previous alarm condition
exists. The update alarm can be configured to operate on a single
channel or on a grouped alarm. eg. master or zoned.
The update alarm is especially useful in systems configured with only
master or group/zone relays, where the occurrence of subsequent
alarms will not cause further relay output compared to that caused by
the initial alarm.
The relevant LED (A1, A2, A3, Fault, Inhibit) will illuminate on the
control card with the alarm condition as described in section 2.3.
When relays are used for signalling update alarms, no other alarms
or messages must be allocated to them. Configuration of update
messages for “inhibit” should be avoided.
l. Rising Alarm
A rising alarm is caused by a rising level of the parameter being
measured crossing a preconfigured threshold and will also cause the
associated alarm LED to illuminate.
