PM866A-2控制單元模塊
在需要將現場接線連接到系統后部，機架中央分為前部和后部各部分由一塊印刷電路板背板組成，提供公共單個信道控制卡之間的功率和信號路由。接口時，通道控制卡安裝在機架前部/繼電器卡直接安裝在通道控制卡的后面機架后部。信道控制卡及其各自接口/繼電器卡通過插頭和插座互連安排在需要將現場接線連接到
系統前端、通道控制卡和接口/繼電器卡一個接一個安裝在6U機架中。底板印刷電路板仍然提供公共電源和信號短路時單個通道控制卡之間的路由卡后部的電纜將每個通道控制卡連接到：它們各自的接口/中繼卡。
使用以下方法對系統進行簡單的校準和檢查：安裝在每個機架上的工程卡上的按鈕。更多可以使用以下之間的RS232鏈路執行復雜配置：工程卡和外部IBM兼容個人運行工程接口軟件的計算機。工程卡可以通過以下方式提供其他功能：插入工程卡的可選模塊。見下文：模塊操作說明手冊：05701M5006 Modbus接口模塊
05701M5007事件打印模塊
05701M5008主報警更新模塊
5701控制系統如圖1所示，概述如下：5701系列控制系統是基于微處理器的系統其顯示連接的氣體檢測器的讀數和狀態。這個系統提供了復雜的報警處理設施，具有完整的維護能力。機架系統配有多個單通道控制卡
每個都有一個相關的現場/中繼卡，提供必要的傳感器輸入和可選繼電器輸出連接。簡單警報
每個通道控制卡提供處理和操作。
復雜的報警處理是通過通過機架背板的指定數量的控制卡。每個機架上都安裝了一個工程卡，用于控制機架背板通信、控制卡詢問和便于維護。此外，安裝到工程卡可以提供額外的系統輸出。系統電源、輔助電源和備用電池系統通常都通過直流輸入卡連接到機架，但是，對于高完整性系統安裝，電源可以是直接連接到每個單獨的控制卡。
In a system where the field wiring is required to be connected to the
rear of the system, the rack is centrally divided into front and rear
sections by a printed circuit board backplane which provides common
power and signal routeing between individual Channel Control Cards.
Channel Control Cards are fitted at the front of the rack while Interface/
Relay cards are fitted directly behind the Channel Control Cards at the
rear of the rack. The Channel Control Cards and their respective
Interface/Relay Cards are interconnected by a plug and socket
arrangement.
In a system where the field wiring is required to be connected to the
front of a system, the Channel Control Cards and Interface/Relay
Cards are mounted one above the other in a 6U rack. The backplane
printed circuit board still provides the common power and signal
routeing between the individual Channel Control Cards while short
cables at the rear of the cards connect each Channel Control Card to
their respective Interface/Relay Card.
Simple calibration and checking of the system is carried out using
push buttons on the Engineering Card fitted to each rack. More
complex configuration can be carried out using the RS232 link between
the Engineering Card and an external IBM compatible personal
computer running the engineering interface software.
Additional functions can be provided by the Engineering Card using
optional modules that plug into the Engineering Card. See the following
module operating instruction manuals:
05701M5006 Modbus Interface Module
05701M5007 Event Printing Module
05701M5008 Master Alarm Update Module
The 5701 Control System is shown in Figure 1 with an overview at
Figure 2.
INTRODUCTION
The 5701 Series Control System is a microprocessor based system
which displays the reading and status of connected gas detectors. The
system provides complex alarm handling facilities with a full
maintenance capability.
A rack system is fitted with a number of single channel control cards
each with an associated field/ relay card which provides the necessary
sensor input and optional relay output connections. Simple alarm
handling and operation is provided by each channel control card.
Complex alarm handling is achieved by communication between a
specified number of control cards via the backplane of the rack.
An engineering card is fitted to each rack and provides control of the
rack backplane communications, control card interrogation and
facilitates maintenance. In addition, optional modules fitted to the
engineering card can provide additional system outputs.
System power supplies, auxiliary power supplies and battery back up
systems are all normally connected to the rack via a DC Input Card,
however, for high integrity system installations power supplies can be
connected directly to each individual control card.
