SNAT603CNT工控卡件
全體的PFTL 101系列中的稱重傳感器有六個不同的測量范圍，從0.5到20kN和兩種不同尺寸（見2.2技術數據）。每個稱重傳感器都經過單獨校準，并且溫度補償。
稱重傳感器通常用六個螺釘（四個）安裝并固定在底座和軸承箱上在稱重傳感器的一側，兩個在相對側。
對于PFTL 101型的所有稱重傳感器，稱重傳感器外殼由一塊鋼加工而成。
然后將傳感器焊接到稱重傳感器室內，并進行定向，使其對測量方向，對其他方向不敏感。
PFTL101A、PFTL 101AE、PFTL101B和PFTL 101 BE型稱重傳感器由不銹鋼制成鋼
PFTL101a和PFTL 101B配備有用于可插拔連接電纜的連接器。
PFTL 101AE和PFTL 101 BE配備有固定連接電纜。
PFTL 101AER和PFTL 101 BER型稱重傳感器是專為安裝在腐蝕環境中而設計的
環境它們由耐酸不銹鋼制成，并具有固定連接纜繩
圖紙中給出了所有稱重傳感器類型的尺寸。精度和精度等級
精度等級定義為最大偏差，并表示為標稱負載下靈敏度的百分比。這包括線性偏差、滯后和重復性誤差。
線性偏差
線性偏差是與輸出值之間繪制的直線的最大偏差
在零負載和標稱負載下。線性偏差與靈敏度有關。遲滯
滯后是在從零開始的一個周期內，相同負載下輸出信號的最大差值
負載到標稱負載和回到零負載，與標稱負載下的靈敏度相關。滯后
壓力傳感器的壓力與負載周期成比例。重復性誤差
重復性誤差定義為相同條件下重復讀數之間的最大偏差
條件它表示為標稱負載下靈敏度的百分比。
補償溫度范圍
在一定溫度下，稱重傳感器的溫度漂移已得到補償
范圍。即規定允許溫度漂移的溫度范圍（即。零點和靈敏度漂移）。
General
The load cells in the PFTL 101 family are available in six different measuring ranges from 0.5 to 20
kN and two different sizes (see 2.2 Technical Data). Each load cell is individually calibrated and
temperature compensated.
The load cells are usually mounted and fixed to a base and a bearing housing with six screws, four
on one side of the load cells and two on the opposite side.
For all load cells of type PFTL 101 the load cell house is machined from a single block of steel.
A sensor is then welded into the load cell house and oriented so that it is sensitive to force in the
direction of measurement and insensitive in other directions.
The load cell types PFTL 101A, PFTL 101AE, PFTL 101B and PFTL 101BE are made of stainless
steel.
PFTL 101A and PFTL 101B are equipped with a connector for the pluggable connection cable.
PFTL 101AE and PFTL 101BE are equipped with a fixed connection cable.
Load cell types PFTL 101AER and PFTL 101BER are specially designed for installation in corrosive
environment. They are made of acid resistant stainless steel and they also have a fixed connection
cable.
Dimensions for all load cell types are given in A Drawings.Accuracy and Accuracy Class
Accuracy class is defined as the maximum deviation, and is expressed as a percentage of the sensitivity at nominal load. This includes linearity deviation, hysteresis and repeatability error.
Linearity Deviation
Linearity deviation is the maximum deviation from a straight line drawn between the output values
at zero load and nominal load. Linearity deviation is related to the sensitivity. Hysteresis
Hysteresis is the maximum difference in the output signal at the same load during a cycle from zero
load to nominal load and back to zero load, related to the sensitivity at nominal load. The hysteresis
of a Pressductor transducer is proportional to the load cycle. Repeatability error
Repeatability error is defined as the maximum deviation between repeated readings under identical
conditions. It is expressed as a percentage of the sensitivity at nominal load.
Compensated temperature range
The temperature drifts of the load cell have been compensated for in certain temperature
ranges. That is the temperature range within which the specified permitted temperature drifts (i.e.
zero point and sensitivity drifts) of the load cell are maintained.
