3BHE024577R0101使用速度，ABB控制器卡件
在負載短路、繞組短路或失速的情況下電機，負載電流將嘗試增加。如前所述如上所述，輸出級的驅動電流被分流（將負載電流限制在1 A左右），導致輸出舞臺線性化。作為輸出的結溫級增加，熱限制電路將變?yōu)椴僮?，進一步降低驅動電流。負載電流（結溫）是環境溫度的函數溫度、剩余驅動器的狀態、電源電壓和負載電阻。如果故障條件得到糾正，則輸出駕駛員將恢復到正常飽和狀態。UIOC和VMIC徽標是的注冊商標VMIC。
3BHE024577R0101使用速度其他注冊商標是其各自所有者。應用程序和配置指南-提供以下應用程序和配置指南從VMIC協助用戶選擇、規范和實施基于VMIC產品的系統。引言VMIVME-2511是一種與VMEbus兼容的可編程輸入/輸出板。它利用兩條摩托羅拉MC68230并行接口定時器I.C.和一條摩托羅拉MC68153總線具有以下特點：48位輸入/輸出（位110，單向8位和16位，雙向8位和16位）
允許四個中斷源的中斷生成邏輯。單定時器中斷每個MC68230一個端口中斷具有64mA接收器功能的可選高電流驅動器（可選）兩個24位可編程定時器軟件可編程定時器模式
可選握手計時器提供了足夠靈活的接口連接到各種低速、中速或高速外圍設備或其他計算機系統Centronics并行接口物理描述VMIVME-2511可編程I10板由VMEbus兼容性組成與并聯相關的邏輯、中斷控制邏輯和I10控制邏輯接口TIRNER模塊。VMEbus兼容邏輯包含地址解碼邏輯和數據傳輸控制邏輯允許VMEbus寫入和讀取數據傳輸。使用摩托羅拉MC68153 BIM的中斷控制邏輯允許端口和定時器從每個并行接口定時器中斷。對CPU的中斷請求當并行接口定時器要求時，由MC68153發出(68230).
In the event of a shorted load, shorted winding, or stalled
motor, the load current will attempt to increase. As described
above, the drive current to the output stage is diverted
(limiting the load current to about 1 A), causing the output
stage to go linear. As the junction temperature of the output
stage increases, the thermal limiting circuit will become
operational, further decreasing the drive current. The load
current (junction temperature) is then a function of ambient
temperature, state of remaining drivers, supply voltage, and
load resistance. If the fault condition is corrected, the output
driver will return to its normal saturated condition.
TRADEMARKS
UIOC and the VMIC logo are registered trademarks of
VMIC. Other registered trademarks are the property of their
respective owners.APPLICATION AND CONFIGURATION GUIDES — The following Application and Configuration Guides are available
from VMIC to assist the user in the selection, specification, and implementation of systems based on VMIC’s products.INTRODUCTION
The VMIVME-2511 is a VMEbus compatible programmable I/O board. It utilizes
two Motorola MC68230 Parallel InterfaceJTimer I.C.'s and one Motorola MC68153 Bus
Interrupter Module and has the following features:
48 Bits of I/O (bit 110, unidirectional 8-bit and 16-bit, bidirectional 8-bit and
16-bit)
Interrupt generation logic allowing four interrupt sources. One timer interrupt
and one port interrupt per MC68230
Optional high current drivers with 64mA sink capability (optional)
Two 24-bit programmable timers
Software programmable timer modes
Selectable handshake timer provides an interface flexible enough for
connection to a wide variety of low, medium or high speed peripherals or other
computer systems
Centronics Parallel Interface
PHYSICAL DESCRIPTION
The VMIVME-2511 Programmable I10 Board consists of VMEbus compatibility
logic, interrupt control logic, and I10 control logic associated with the parallel
interfaceltirner modules.
The VMEbus compatibility logic contains address decoding logic and data
transfer control logic allowing VMEbus write and read data transfers.
Interrupt control logic which utilizes the Motorola MC68153 BIM allows port and
timer interrupts from each parallel interfaceltimer. The interrupt requests to the CPU
are issued by the MC68153 when requested to do so by the parallel interfaceltimer
(68230).
