PP877K觸摸屏,ABB操作面板
功能特性合規性：本產品符合VMEbus規范版本。C、 1具有以下內容
助記符：A16:D32，D16，D08（EO）：29，2D：從6U形狀系數地址修改器代碼：跳線可選短監督或短非特權輸入/輸出訪問。工廠配置為短監督輸入/輸出訪問。尋址方案：分別四個端口
可在8位、16位或32位邊界上尋址。這個用于控制和狀態寄存器（CSR）和板ID寄存器允許要分組的硬件控制地址提高了軟件效率。
PP877K觸摸屏數據傳輸：支持8位、16位或32位數據轉移輸出規格摘要輸出組織：四個端口，八位寬?？蓪ぶ返蕉虝r間內的任何地址，或短非特權輸入/輸出映射。輸出特性：大電流驅動器（600 mA接收器）輸出設計用于驅動白熾燈無外部電流限制或加熱電阻器。由于冷燈絲涌流，建議只有一個燈由輸出驅動器。但是，如果必須安裝多個燈泡由單根導線驅動，則可能需要另一個驅動器并聯連接。如果必須安裝多個燈泡由單輸出驅動，建議
VMIVME-2131（電流源/匯）或使用VMIVME-2130（僅限電流源）。輸出驅動器還具有以下特點：熱電流停機保護，高擊穿電壓（60 V），和用于感應反激的輸出箝位二極管保護有關輸出驅動器設計的詳細信息和說明見第3頁。TTL或電子開關輸出的上拉電阻器為可選擇的輸出維持電壓：最小35 V過流保護輸出電壓：25 V輸出飽和電壓：見表3和表4輸出數據選項：正true或負true選項輸入規范摘要單端信號輸入特性：高輸入阻抗（33 k?). 閾值精度為1在整個60 V范圍內的百分比（典型）。提到圖4為典型單端信號調節電子學差分信號輸入特性：共模輸入電壓范圍：-30至+60 V輸入在-7的共模范圍內靈敏度為±100 mV至+12 V高輸入阻抗（33 k?)
FUNCTIONAL CHARACTERISTICS
Compliance: This product complies with the
VMEbus specification Rev. C. 1 with the following
mnemonics:
A16:D32, D16, D08 (EO): 29, 2D: Slave
6U form factor
Address Modifier Codes: Jumper-selectable for
short supervisory or short nonprivileged I/O access.
Factory configured for short supervisory I/O access.
Addressing Scheme: Four ports individually
addressable on 8-, 16-, or 32-bit boundaries. The
separate board address decoder for the Control and
Status Register (CSR) and Board ID Register allows
addresses for hardware control to be grouped for
improved software efficiency.
Data Transfer: Supports 8-, 16-, or 32-bit data
transfers
OUTPUT SPECIFICATION SUMMARY
Output Organization: Four ports, eight bits wide.
Addressable to any address within short supervisory or
short nonprivileged I/O map.
Output Features: The high-current driver (600 mA
sink) outputs are designed to drive incandescent lamps
and inductive loads without external current limiting or
warming resistors. Due to cold filament inrush currents,
it is recommended that only one lamp be driven by the
output driver. However, if more than one bulb must be
driven by a single wire, then another driver may be
connected in parallel. If more than one bulb must be
driven by a single output, it is recommended the
VMIVME-2131 (current source/sink) or the
VMIVME-2130 (current source only) be used.The output drivers also feature: thermal current
shutdown protection, high breakdown voltage (60 V),
and output clamp diodes for inductive flyback
protection. Details concerning the output driver design
and description are shown on page 3.
Pull-up resistors for TTL or electronic switch outputs are
optional.
Output Sustaining Voltage: 35 V minimum
Overcurrent Protected Output Voltage: 25 V
Output Saturation Voltage: See Tables 3 and 4
Output Data Option: Positive true or negative true
options
INPUT SPECIFICATION SUMMARY
Single-Ended Signal Input Characteristics: High
input impedance (33 k?). Threshold accuracy of 1
percent over entire 60 V range (typical). Refer to
Figure 4 for typical single-ended signal conditioning
electronics.
Differential Signal Input Characteristics:
Common-mode input voltage range: -30 to + 60 V Input
sensitivity of ±100 mV over common-mode range of -7
to +12 V
High input impedance (33 k?)
