VIBRO 200-560-101-015卡件實驗數據
如果出現以下情況，MVME2600和MVME712兼容型號將受損：錯誤地連接到MVME761轉換模塊，而不是更正MVME712系列電路板。MVME2603/2604型號中的注釋MVME712M輸入/輸出模式，VMEbus的引腳分配連接器P2與其他過渡模塊完全兼容MVME712系列。在這種情況下，存在可能導致死亡的危險電壓設備搬運、測試和調整時要格外小心。
VIBRO 200-560-101-015卡件實驗數據3機箱的前部或后部。（您可能需要將其他模塊移入機箱為MVME712M留出空間，MVME712M具有雙寬前面板。）4.將P2適配器板連接到插槽處的P2背板連接器被MVME2603/2604 VME模塊占用。5、將配備MVME712M的64芯電纜從P2適配器板上的J2連接到過渡模塊上的J2。一定要用接頭針腳1定位電纜針腳1。避免接觸集成電路的區域；靜電放電會損壞這些電路
6、使用提供的螺釘將MVME712M固定在機箱中，與橫向安裝軌道接觸良好，以將射頻發射。
7、參考MVME712M的用戶手冊（見附錄D，相關文件），50芯電纜的布線適用于您的系統配置。確保用連接器定位電纜針腳1針腳1。注意：SCSI布線可以通過多種方式進行配置，以適應各種設備和系統配置。圖形1-21顯示了與內部SCSI一起使用的可能配置設備。有關安裝P2的更多詳細信息適配器板和MVME712M轉換模塊，請參閱用戶手冊（在附錄D中列出，相關文件）。8.更換機箱或系統蓋，確保沒有電纜擠壓。用電纜將外圍設備連接到面板連接器，然后重新連接將系統接至交流或直流電源，并轉動設備打開電源。注：并非所有外圍電纜均配備MVME712M；你可能需要制造或購買某些電纜。（最小化輻射，摩托羅拉建議外圍設備使用屏蔽電纜盡可能連接。）
The MVME2600, MVME712-compatible models will be damaged if
mistakenly connected to the MVME761 transition modules instead of the
correct MVME712 family of boards.
Note In models of the MVME2603/2604 that are configured for
MVME712M I/O mode, the pin assignments of VMEbus
connector P2 are fully compatible with other transition modules
of the MVME712 series. Dangerous voltages, capable of causing death, are present in this
equipment. Use extreme caution when handling, testing, and adjusting.
3. Remove the filler panel(s) from the appropriate card slot(s) at the
front or rear of the chassis. (You may need to shift other modules in
the chassis to allow space for the MVME712M, which has a doublewide front panel.)
4. Attach the P2 adapter board to the P2 backplane connector at the slot
occupied by the MVME2603/2604 VME module.
5. Route the 64-conductor cable furnished with the MVME712M from
J2 on the P2 adapter board to J2 on the transition module. Be sure to
orient cable pin 1 with connector pin 1.
Avoid touching areas of integrated circuitry; static discharge can damage
these circuits
6. Secure the MVME712M in the chassis with the screws provided,
making good contact with the transverse mounting rails to minimize
RF emissions.
7. Referring to the user’s manual for the MVME712M (listed in
Appendix D, Related Documentation), route the 50-conductor cable
to the internal or external SCSI devices as appropriate to your
system configuration. Be sure to orient cable pin 1 with connector
pin 1.
Note The SCSI cabling can be configured in a number of ways to
accommodate various device and system configurations. Figure
1-21 shows a possible configuration for use with internal SCSI
devices. For more detailed information on installing the P2
adapter board and the MVME712M transition module, refer to
the user’s manual (listed in Appendix D, Related
Documentation).8. Replace the chassis or system cover(s), making sure no cables are
pinched. Cable the peripherals to the panel connectors, reconnect
the system to the AC or DC power source, and turn the equipment
power on.
Note Not all peripheral cables are provided with the MVME712M; you
may need to fabricate or purchase certain cables. (To minimize
radiation, Motorola recommends shielded cable for peripheral
connections where possible.)
