VIBRO 200-560-000-016模塊,數據庫
將填充板從要插入的卡槽中卸下安裝MVME2603/2604。–如果您打算使用MVME2603/2604作為系統控制器，它必須占用最左邊的卡槽（槽1）。系統控制器必須在插槽1中才能正確啟動總線授權并確保IACK daisychain驅動器的正確操作。如果您不打算使用MVME2603/2604 as系統控制器，它可以占用任何未使用的雙高卡插槽。
VIBRO 200-560-000-016模塊4、將MVME2603/2604滑入所選卡槽。確保模塊位于背板上的P1和P2連接器中。不要損壞或彎曲連接器針腳。5.用螺釘將MVME2603/2604固定在機箱中與橫向安裝軌道良好接觸，以盡量減少射頻發射。
6.在機箱背板上，刪除中斷確認卡頭的（IACK）和總線授權（BG）跳線MVME2603/2604占用的插槽。注意一些VME背板（例如，摩托羅拉使用的那些“模塊化底盤”系統）具有自動跳線功能IACK和BG信號的自動傳播。第6步不適用于此類背板設計。如有必要，安裝MVME712M或MVME761過渡段模塊并將其連接至MVME2603/2604，如本文件的以下章節。8.將機箱或系統蓋、電纜外圍設備更換到根據需要，將系統重新連接到交流或直流電源，并打開設備電源。MVME712M過渡模塊安裝本節適用于MVME712M兼容型號的MVME2603/2604 VME模塊。安裝MVME2603/2604后，參考圖1-21，按照以下步驟安裝MVME712M過渡模塊：
1、將靜電帶系在手腕上。連接ESD的另一端將皮帶系在底盤上作為接地。靜電放電帶必須固定在在整個過程中，您的手腕和地面。2、執行操作系統關機。接通交流或直流電源斷開并從系統中卸下交流電源線或直流電源線。拆下機箱或sy
3. Remove the filler panel from the card slot where you are going to
install the MVME2603/2604.
– If you intend to use the MVME2603/2604 as system controller,
it must occupy the left-most card slot (Slot 1). The system
controller must be in Slot 1 to correctly initiate the bus-grant
daisy-chain and to ensure proper operation of the IACK daisychain driver.
– If you do not intend to use the MVME2603/2604 as system
controller, it can occupy any unused double-height card slot.
4. Slide the MVME2603/2604 into the selected card slot. Be sure the
module is well seated in the P1 and P2 connectors on the backplane.
Do not damage or bend connector pins.5. Secure the MVME2603/2604 in the chassis with the screws
provided, making good contact with the transverse mounting rails to
minimize RF emissions.
6. On the chassis backplane, remove the INTERRUPT ACKNOWLEDGE
(IACK) and BUS GRANT (BG) jumpers from the header for the card
slot occupied by the MVME2603/2604.
Note Some VME backplanes (for example, those used in Motorola
"Modular Chassis" systems) have an auto-jumpering feature for
automatic propagation of the IACK and BG signals. Step 6 does
not apply to such backplane designs.7. If necessary, install an MVME712M or MVME761 transition
module and cable it to the MVME2603/2604 as described in the
following sections of this document.
8. Replace the chassis or system cover(s), cable peripherals to the
panel connectors as appropriate, reconnect the system to the AC or
DC power source, and turn the equipment power on.
MVME712M Transition Module Installation
This section applies to MVME712M-compatible models of the
MVME2603/2604 VME module. With the MVME2603/2604 installed,
refer to Figure 1-21 and proceed as follows to install an MVME712M
transition module:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD
strap to the chassis as a ground. The ESD strap must be secured to
your wrist and to ground throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power
off and remove the AC cord or DC power lines from the system.
Remove chassis or sy
