VIBRO 200-510-111-013工控卡件，參數說明
PMC承載板安裝PCI夾層卡（PMC）承載板安裝在RAM200上方MVME2603/2604基座上的夾層和（如果安裝）PMC模塊板要安裝用于額外PCI擴展的PMC載體板，請參閱按照圖1-20進行操作：1、將靜電帶系在手腕上。連接ESD的另一端將皮帶系在底盤上作為接地。靜電放電帶必須固定在在整個過程中，您的手腕和地面。
VIBRO 200-510-111-013工控卡件2、執行操作系統關機。接通交流或直流電源斷開并從系統中卸下交流電源線或直流電源線。根據需要卸下機箱或系統蓋，以便訪問VME模塊。圖1-20。PMC載體板在MVME2603/2604上的放置5.卸下位于上前角的LED模塊螺釘基板。在其位置6安裝一個短（0.394英寸）支架。在基板的其他三個角落，安裝長（0.737英寸）對峙。
7、將PMC承載板放置在基板頂部。連接器在承載板的底面上，應與上相應的接頭J5（位于P1和P2之間）MVME2603/2604。
8.將四個短十字螺釘穿過拐角處的孔在MVME2603/2604上的支架上。擰緊螺釘。
9.將MVME2603/2604組件重新安裝到其正確的卡槽中。是確保模塊正確安裝在背板連接器中。不要損壞或彎曲接頭針腳。10.更換機箱或系統護蓋，將系統重新連接到交流或直流電源，并打開設備電源。MVME2603/2604 VME模塊安裝安裝夾層板并正確配置標頭后，按照以下步驟在VME機箱中安裝MVME2603/2604：1、將靜電帶系在手腕上。連接ESD的另一端將皮帶系在底盤上作為接地。靜電放電帶必須固定在在整個過程中，您的手腕和地面。
2、執行操作系統關機。接通交流或直流電源斷開并從系統中卸下交流電源線或直流電源線。根據需要卸下機箱或系統蓋，以便訪問VME模塊。
PMC Carrier Board Installation
PCI mezzanine card (PMC) carrier boards mount above the RAM200
mezzanine and (if installed) PMC module on the MVME2603/2604 base
board. To install a PMC carrier board for additional PCI expansion, refer
to Figure 1-20 and proceed as follows:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD
strap to the chassis as a ground. The ESD strap must be secured to
your wrist and to ground throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power
off and remove the AC cord or DC power lines from the system.
Remove chassis or system cover(s) as necessary for access to the
VME modules.Figure 1-20. PMC Carrier Board Placement on MVME2603/2604
5. Remove the LED module screw located at the upper front corner of
the base board. Install a short (0.394 inch) standoff in its place6. At the other three corners of the base board, install long (0.737 inch)
standoffs.
7. Place the PMC carrier board on top of the base board. The connector
on the underside of the carrier board should connect smoothly with
the corresponding connector J5 (located between P1 and P2) on the
MVME2603/2604.
8. Insert the four short Phillips screws through the holes at the corners
of the carrier board, into the standoffs on the MVME2603/2604.
Tighten the screws.
9. Reinstall the MVME2603/2604 assembly in its proper card slot. Be
sure the module is well seated in the backplane connectors. Do not
damage or bend connector pins.
10. Replace the chassis or system cover(s), reconnect the system to the
AC or DC power source, and turn the equipment power on.
MVME2603/2604 VME Module Installation
With mezzanine board(s) installed and headers properly configured,
proceed as follows to install the MVME2603/2604 in the VME chassis:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD
strap to the chassis as a ground. The ESD strap must be secured to
your wrist and to ground throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power
off and remove the AC cord or DC power lines from the system.
Remove chassis or system cover(s) as necessary for access to the
VME modules.
