3BSE050199R1控制器模塊,PM866K02使用說明
硬件配置產生所需的配置并確保MVME2603/2604，您可能需要執行某些硬件安裝模塊前的修改。MVME2603/2604提供了對大多數選項的軟件控制：通過在系統中安裝模塊后，在控制寄存器中設置位可以修改其配置。（MVME2603/2604控制寄存器為如第3章功能描述和/或MVME2600中所述系列單板計算機程序員參考指南，如中所列附錄D，相關文件。）
3BSE050199R1控制器模塊然而，有些選項不是軟件可編程的。這些選項包括通過手動安裝或拆除收割臺跳線或基板上的接口模塊或相關轉換模塊VME2603/2604基板準備第1-9頁的圖1-2說明了開關、跳線的位置MVME2603/2604上的標題、連接器和LED指示燈?；迳峡墒謩?dòng)配置的項目包括：? 緩存模式控制（J3）? 閃存組選擇（J10）? 串行端口4接收時鐘配置（J16）? 串行端口4傳輸時鐘配置（J17）? 串口4發送時鐘接收器緩沖控制（J20）? 串行端口3傳輸時鐘配置（J18）? 系統控制器選擇（J22）結合基板上的串行端口設置，串行端口在相關的MVME712M或MVME761過渡模塊上可手動配置。用于討論過渡模塊，參見MVME712M過渡模塊準備第1-14頁，第1-25頁MVME761過渡模塊準備，或轉換模塊的相應用戶手冊（在中列出附錄D，相關文件），如有必要。MVME2603/2604經過工廠測試，并隨以下各節中描述的配置。這個MVME2603/2604的要求和工廠安裝的調試監視器，PPCBug使用這些出廠設置。
Hardware Configuration
To produce the desired configuration and ensure proper operation of the
MVME2603/2604, you may need to carry out certain hardware
modifications before installing the module.
The MVME2603/2604 provides software control over most options: by
setting bits in control registers after installing the module in a system, you
can modify its configuration. (The MVME2603/2604 control registers are
described in Chapter 3, Functional Description, and/or in the MVME2600
Series Single Board Computer Programmer’s Reference Guide, as listed in
Appendix D, Related Documentation.)
Some options, however, are not software-programmable. Such options are
controlled through manual installation or removal of header jumpers or
interface modules on the base board or the associated transition moduleMVME2603/2604 Base Board Preparation
Figure 1-2 on page 1-9 illustrates the placement of the switches, jumper
headers, connectors, and LED indicators on the MVME2603/2604.
Manually configurable items on the base board include:
? Cache mode control (J3)
? Flash bank selection (J10)
? Serial Port 4 receive clock configuration (J16)
? Serial Port 4 transmit clock configuration (J17)
? Serial Port 4 transmit clock receiver buffer control (J20)
? Serial Port 3 transmit clock configuration (J18)
? System controller selection (J22)
In conjunction with the serial port settings on the base board, serial ports
on the associated MVME712M or MVME761 transition module are also
manually configurable. For a discussion of the configurable items on the
transition module, refer to MVME712M Transition Module Preparation
on page 1-14, MVME761 Transition Module Preparation on page 1-25, or
to the respective user’s manuals for the transition modules (listed in
Appendix D, Related Documentation) as necessary.
The MVME2603/2604 is factory tested and shipped with the
configurations described in the following sections. The
MVME2603/2604’s required and factory-installed debug monitor,
PPCBug, operates with those factory settings.
