GJR2209300R0001卡件，ABB使用配置教程
特征這些是MVME197LE單板的一些主要功能計算機：
? MC88110 RISC微處理器? 32或64兆字節的64位動態隨機存取存儲器（DRAM）帶糾錯功能
? 1兆字節的閃存? 六個狀態指示燈（故障、運行、SCON、LAN、SCSI和VME）
? 8KB的靜態隨機存取存儲器（SRAM）和時間帶電池備用RAM（BBRAM）的（TOD）時鐘
? 兩個按鈕開關（中止和重置）? 128 KB的啟動ROM
? 六個用于周期性中斷的32位滴答計時器? 看門狗定時器
GJR2209300R0001卡件? 八次軟件中斷? 輸入/輸出
–具有直接內存訪問（DMA）的SCSI總線接口–四個帶EIA-232-D緩沖器的串行端口
–Centronics打印機端口–以太網收發器接口
? VMEbus接口–VMEbus系統控制器功能
–VMEbus與本地外圍總線的接口（A24/A32、D8/D16/D32BLT（D8/D16/D32/D64））（BLT=塊傳輸）–本地外圍總線至VMEbus接口（A24/A32、D8/D16/D32BLT（D16/D32/D64））–VMEbus中斷功能描述以下各節包含上主要模塊的功能描述MVME197LE單板計算機。前面板開關和指示燈面板上有兩個按鈕開關和六個LEDMVME197LE模塊。開關復位并中止。重置如果出現以下情況，開關（S3）將重置所有車載設備并驅動SYSRESET*信號：板是系統控制器。重置開關（S3）將重置所有車載設備如果電路板不是系統控制器，則為DCAM和ECDM以外的設備。VMEchip2生成SYSREST*信號?？偩€開關結合了本地重置和重置開關，以生成本地板重置。參考重置MVME197LE、MVME197DP和MVME197SP單板計算機程序員參考指南
Features
These are some of the major features of the MVME197LE single board
computer:
? MC88110 RISC Microprocessor
? 32 or 64 megabytes of 64-bit Dynamic Random Access Memory (DRAM)
with error correction
? 1 megabyte of Flash memory
? Six status LEDs (FAIL, RUN, SCON, LAN, SCSI, and VME)
? 8 kilobytes of Static Random Access Memory (SRAM) and Time of Day
(TOD) clock with Battery Backup RAM (BBRAM)
? Two push-button switches (ABORT and RESET)
? 128 kilobytes of BOOT ROM
? Six 32-bit tick timers for periodic interrupts
? Watchdog timer
? Eight software interrupts
? I/O
– SCSI Bus interface with Direct Memory Access (DMA)
– Four serial ports with EIA-232-D buffers
– Centronics printer port
– Ethernet transceiver interface
? VMEbus interface
– VMEbus system controller functions
– VMEbus interface to local peripheral bus (A24/A32, D8/D16/D32
BLT (D8/D16/D32/D64))(BLT = Block Transfer)
– Local peripheral bus to VMEbus interface (A24/A32, D8/D16/D32
BLT (D16/D32/D64))
– VMEbus interrupterFunctional Description
The following sections contain a functional description of the major blocks on
the MVME197LE single board computer.
Front Panel Switches and Indicators
There are two push-button switches and six LEDs on the front panel of the
MVME197LE module. The switches are RESET and ABORT. The RESET
switch (S3) will reset all onboard devices and drive the SYSRESET* signal if the
board is the system controller. The RESET switch (S3) will reset all onboard
devices except the DCAM and ECDM if the board is not the system controller.
The VMEchip2 generates the SYSREST* signal. The BusSwitch combines the
local reset and the reset switch to generate a local board reset. Refer to the Reset
Driver section in the VMEchip2 chapter of the MVME197LE, MVME197DP, and
MVME197SP Single Board Computers Programmer’s Reference Guide for more
information
