5SHY3545L0020可控硅模塊,5SHY3545L0020使用數量
用于支持CPU 374的標準90-30系列3伏鋰電池的預期壽命為1.2個月連續使用時。如果需要更長的電池備份時間，則外部電池模塊（IC693ACC302）可用。外部電池模塊為以下各項提供15個月的電池備用期：CPU374。有關更多信息，請參閱外部電池組數據表GFK-2124。覆蓋未存儲到閃存或EZ程序存儲設備將參考數據存儲到閃存或EZ程序存儲設備時，不會存儲覆蓋。這意味著在從閃存或EZ程序存儲設備讀回參考數據后，然后PLC處于運行模式，邏輯可能會以不同方式執行。
5SHY3545L0020可控硅模塊因此，在以下情況下不應使用覆蓋：參考數據存儲到閃存或EZ程序存儲設備。如果使用覆蓋，請?zhí)貏e注意應防止在通電時從閃存加載參考數據。如果不遵守此預防措施，斷電后可能會發生意外操作。使用串行編程器編寫Flash在將超大程序?qū)懭腴W存時，可能需要增加中的請求超時值用于避免接收請求超時消息的編程軟件。25秒的上限為通常令人滿意。有關更多詳細信息，請參閱項目“將程序或參考表存儲到Flash may”第6頁“以太網操作說明”中的“導致以太網通信丟失”。存儲大型配置使用CPU 374的90-30系列PLC最多支持32個DSM314模塊。這個數字減少了當PLC中使用其他智能模塊時，如APM和GBC模塊。也可以減少什么時候：■ PLC中的機架數量增加；■ 邏輯、運動和AUP文件的總大小增加；■ 應用程序使用C邏輯塊或C邏輯程序；和■ 連接的編程器或HMI設備用于讀取參考存儲器或故障表。在某些情況下，可能會增加CPU 374將接受的DSM314模塊的數量在硬件配置中，首先存儲邏輯，然后單獨存儲配置同時加載和存儲在連接多個編程器的情況下操作時，從一個編程器啟動存儲操作來自另一個程序員的加載操作將導致加載失敗。清除參考表時，不會清除過渡表通過編程器清除參考表時，不會清除轉換表。
Battery Backup Limitations
The expected life of a standard Series 90-30 3-volt lithium battery used to back up a CPU 374 is 1.2 months
when used continuously. If a longer battery backup period is required, the external battery module
(IC693ACC302) is available. The external battery module provides a battery backup period of 15 months for
the CPU374. For additional information, see the External Battery Pack datasheet, GFK-2124.
Overrides Not Stored to Flash or EZ Program Store Device
When storing reference data to flash or the EZ Program Store Device, overrides are not stored. This means
that after the reference data is read back from flash or the EZ Program Store Device and subsequently the
PLC is put into Run Mode, the logic may execute differently. Therefore, overrides should not be used if
reference data is stored to flash or to the EZ Program Store Device. If overrides are used, particular care
should be taken to prevent loading reference data from flash at power up. If this precaution is not observed,
unexpected operation may occur upon power cycle.
Writing Flash Using a Serial Programmer
When writing very large programs to flash memory, you may need to increase the request timeout value in
the programming software to avoid receiving a request timeout message. An upper bound of 25 seconds is
typically satisfactory. For further details, see the item “Store of Program or Reference Tables to Flash may
Cause Loss of Ethernet Communications” in “Ethernet Operational Notes” on page 6.
Storing Large Configurations
A Series 90-30 PLC using a CPU 374 supports a maximum of 32 DSM314 modules. This number is reduced
when other intelligent modules are used in the PLC, such as APM and GBC modules. It may also be reduced
when:
■
The number of racks in the PLC increases;
■
The total size of logic, motion and AUP files increases;
■
The application uses C logic blocks or a C logic program; and
■
Connected programmers or HMI devices are used to read reference memory or fault tables.
In some cases it may be possible to increase the number of DSM314 modules that the CPU 374 will accept
in the hardware configuration by storing logic first and then storing the configuration separately.
Simultaneous Load and Store
When operating with multiple programmers attached, initiating a store operation from one programmer during
a load operation from another programmer will cause the load to fail.
Transition Tables are not Cleared when the Reference Tables are Cleared
The transition tables are not cleared upon clearing the reference tables through the programmer.
