PPC905AE101控制模塊,PPC905AE101使用尺寸
模塊的輸入保護足以保證在性能降低的情況下運行高達200V共模。該模塊提供外部電氣隔離
通過使用光學隔離在現場布線和背板之間產生噪聲。為了將電容性負載和噪聲降至最低，模塊的所有現場連接應使用優質絞合屏蔽儀表電纜接線。防護罩可以是連接到COM或GND。COM連接提供對模塊中的模擬電路。接地連接提供對基板（框架）的訪問接地）。
PPC905AE101控制模塊當模塊的電源工作時，面板頂部的LED亮起。主要模塊的電源是由PLC電源提供的隔離+24 VDC電源。該電壓通過逆變器/調節器傳輸，為模塊提供工作電壓。該模塊還消耗PLC電源+5 VDC輸出的電力，以驅動隔離電路。該模塊可以安裝在90-30系列PLC系統。見第3-11頁，以確定模擬電流輸入的數量可以安裝在系統中的模塊為了限制共模電壓，每個電流源公共線可以如果信源是浮動的，也要綁定到其相關的COM終端。這些可選連接如上圖所示。有關接線和屏蔽接地連接的詳細信息，請參閱第2章。默認范圍為4至20 mA，用戶數據按比例縮放，使4 mA對應于0計數20 mA對應32000個計數，每1000個計數代表0.5 mA。什么時候在輸入/輸出端子板上添加跳線，輸入范圍隨用戶更改為0至20 mA對數據進行縮放，使0 mA對應于0的計數，20 mA對應于0的計數32000，每800個計數代表0.5 mA。隨附兩個范圍跳線單元一個用于通道1和2，另一個用于通道3和4。
Input protection for the module is sufficient to guarantee operation with reduced performance
with up to 200V common-mode. The module provides electrical isolation of externally
generated noise between field wiring and the backplane through the use of optical isolation.
To minimize the capacitive loading and noise, all field connections to the module should be
wired using a good grade of twisted, shielded instrumentation cable. The shields can be
connected to either COM or GND. The COM connection provides access to the common of the
analog circuitry in the module. The GND connection provides access to the baseplate (frame
ground).
An LED at the top of the faceplate is ON when the module’s power supply is operating. The main
power source for the module is the isolated +24 VDC power supplied by the PLC power supply.
This voltage is routed through an inverter/regulator to provide the operating voltage for the module.
This module also consumes power from the +5 VDC output of the PLC power supply to drive the
isolation circuitry. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a
Series 90-30 PLC system. See page 3-11 to determine the number of Analog Current Input
modules that can be installed in a systemIn order to limit common-mode voltages, each current source common line may
also be tied to its associated COM terminal if the source is floating. These
optional connections are shown in the figure above.
Please refer to Chapter 2 for wiring and shield ground connection details.The default range is 4 to 20 mA with user data scaled so that 4 mA corresponds to a count of 0
and 20 mA corresponds to a count of 32000 with each 1000 counts representing 0.5 mA. When
a jumper is added to the I/O terminal board, the input range is changed to 0 to 20 mA with user
