NU8976A99處理器模塊,NU8976A99配置教程
端子5至46用于現場設備。每個終端接受一個AWG#14線（平均橫截面2.1mm2），2 AWG#14（2.1mm2交叉截面）實心導線，或兩個AWG#16（每個平均1.3mm2橫截面）絞合線。任何電路都可以是輸入或輸出。連接場的一個端子設備連接到直流電源，另一個連接到模塊（端子10-41）。所有輸入/輸出設備必須返回同一電源電路。根據布局和電流負載，正極和負極連接可以通過總線連接，并通過單線連接到塊或電源。
NU8976A99處理器模塊直流電源塊的連接對于源塊，將輸出連接到電源的負極正極的電源和輸入如果電路電源未與塊電源同時斷開，則
當激活多個輸入時，模塊可能通電，甚至盡管有一條腿的力量已經從街區中消失了。如果您想在不切斷輸入電源的情況下禁用塊設備，使用塊拉拔器拔下電子組件。不要斷開H或N以斷開電源。直流接收器塊的連接對于接收器塊，將輸出連接到電源的正極和輸入到負極。將直流電源連接到直流+端子（6-9）和直流回路-端子（42-46）直流匯接塊，電源斷開由于塊功率與電路功率相同，因此接線很重要塊電源斷開，以便塊電源和輸入電源將同時刪除。如圖所示，找到電源斷開裝置在下面直流接收器塊直流+負荷DC 否是注意安全如果電路電源未與塊電源同時斷當激活多個輸入時，模塊可能通電，甚至盡管有一條腿的力量已經從街區中消失了。如果您想在不切斷輸入電源的情況下禁用塊設備，使用塊拉拔器拔下電子組件。不要斷開H或N以斷開電源。
Terminals 5 to 46 are for field devices. Each terminal accepts one AWG
#14 wire (avg 2.1mm2 cross section), two AWG #14 (2.1mm2
cross
section) solid wires, or two AWG #16 (each avg 1.3mm2
in cross section)
stranded wires.
Any circuit can be an input or output. Connect one terminal of a field
device to DC power and the other to the block (terminals 10-41). All I/O
devices must return to the same power circuit.
Depending on layout and current loads, positive and negative
connections can be bussed and made by single wires to the block or
power source.
Connections for a DC Source Block
For a Source block, connect outputs to the negative side of the power
supply and inputs to the positive sideIf circuit power is not removed at the same time as block power, the
block may power up when multiple inputs are activated, even
though one leg of power has been removed from the block.
If you want to disable the block without removing power from input
devices, use a Block Puller to unplug the Electronics Assembly. Do not
disconnect H or N to remove power.Connections for a DC Sink Block
For a Sink block, connect outputs to the positive side of the power supply
and inputs to the negative side. Connect a DC source to the DC+
terminals (6-9) and the return to the DC- terminals (42-46)DC Sink Block, Power Disconnects
Since block power is the same as circuit power, it is important to wire
block power disconnects so that block power and input power will be
removed at the same time. Locate the power disconnect as shown
below. DC SINK
BLOCK
DC+
LOAD
DCNO YES
CAUTION
If circuit power is not removed at the same time as block power,
the block may power up when multiple inputs are activated, even
though one leg of power has been removed from the block.
If you want to disable the block without removing power from input
devices, use a Block Puller to unplug the Electronics Assembly. Do not
disconnect H or N to remove power.
