1SBP260011R1001數控系統模塊,1SBP260011R1001使用指導
使用外部開/關開關（未提供）啟動和關閉張力電子設備ABB）。正常維修期間，無需操作員采取任何行動。
檢查主張力控制機械是否準備好正常運行。
通過將外部開/關開關設置到on位置，打開張力電子設備。
對于IP 65版本（NEMA 4），也將內部開關設置為“ON”。
檢查：-顯示屏點亮-“電源”指示燈點亮-“狀態”指示燈亮起（綠燈）。紅燈指示錯誤。通過將外部接通/斷開開關設置到斷開位置，關閉張力電子設備。
1SBP260011R1001數控系統模塊,4.5正常運行測量設備應永久開啟，以獲得最佳測量結果。這允許稱重傳感器和電子設備在均勻的溫度條件下工作。
測量設備設計用于連續測試顯示的測量值示例：
所選單位[N]，稱重傳感器標稱荷載100 kN，測量值987654 N。顯示值：987600 N。
選定單位【kN】，稱重傳感器標稱荷載100 kN，測量值987654 N。顯示值：987.6 kN。
與設置小數功能一起顯示的測量值示例：
選定單位【pli】，稱重傳感器標稱荷載1 kN，測量值46.5987 pli。
設置小數=2顯示值：46.60 pli。
選定單位【pli】，稱重傳感器標稱荷載1 kN，測量值46.5987 pli。設置小數=0顯示值：47 pli。
The tension electronics is started and shut down using an external ON/OFF switch (not supplied
by ABB). During normal service no action from the operator is required.
1. Check that the main tension control machinery is ready for normal run.
2. Switch on the tension electronics by setting the external ON/OFF switch to position ON.
For the IP 65-version (NEMA 4) also set the internal switch to “ON”.
3. Check that:
- the display is illuminated
- the “Power” indicator is lit
- the “Status” indicator is lit (green light). Red light indicates an error.Shut-down the tension electronics by setting the external ON/OFF switch to position OFF.
4.5 Normal Run
The measurement equipment should be permanently on to achieve best measuring result. This
allows the load cells and electronics to operate under even temperature conditions.
The measuring equipment is designed for continuous dutyExamples of measuring values displayed:
Example 1:
Selected unit [N], Load cell nominal load 100 kN, Measured value 987654 N.
Value presented on display: 987600 N.
Example 2:
Selected unit [kN], Load cell nominal load 100 kN, Measured value 987654 N.
Value presented on display: 987.6 kN.
Examples of measuring values displayed together with the Set Decimals function:
Example 1:
Selected unit [pli], Load cell nominal load 1 kN, Measured value 46.5987 pli.
